Oh yes - didn't reply to the "chip_h", in asus patch called "chip_enable_h".
This is the <&gpio4 RK_PD3 GPIO_ACTIVE_LOW> IIRC. We could see that two
pins were pulled. RK_PD3 and RK_PD4; but not knowing exactly why the
pins were pulled, question is should they be separate?
We went the direction of putting both pins under wifi_enable.
Its not clear to me which is the least confusing, should wifi_enable
need pulling two pins, or should there be an extra service
"chip_enable_h" for the extra pin? Think our problem is we didn't see
what "chip_enable_h" meant - the description doesn't help. Hence why we
removed, and merged with wifi_enable ...
On 17/02/2019 14:32, Tony McKahan wrote:
A similar configuration has been in use on Armbian images since kernel
4.14, but not in a clean enough format for submission. I will test
this, but the only differences I see compared to ours are combination
of the mystery "chip_h" power domain/reset with the Wifi one and the
inclusion of sd_uhs_ddr50.
-Tony
On Sun, Feb 17, 2019 at 7:16 AM David Summers
<beagleboard@xxxxxxxxxxxxxxxxxxx> wrote:
This patch adds the wifi to the ASUS Tinker Board (S) machines.
Unfortunatly neither the Tinker Board nor the Tinker Board S schematic
indicate how the WiFi is wired up on these devices. The WiFi is
provided by the RTL8723BS device, that has sdio WiFi and UART
Bluetooth. This patch just adds the WiFi interface.
With no schematic, most of the wiring has been derived from the ASUS
patch to Debian:
https://github.com/TinkerBoard/debian_kernel/commit/6a3128ade33f758887048578ada61a4b7ab8e678
In conjunction with the pin out of the RTL8723BS device:
http://files.pine64.org/doc/datasheet/pine64/RTL8723BS.pdf
http://cit.odessa.ua/media/pdf/Intel-Compute-Stick/FN-Link_F23BDSM25-W1.pdf
The only unusual part is that to bring the card up, both the pins
RK_PD3 and RK_PD4 need to be pulled. Why this needs to be done is not
clear, best explaination is that they are connected to the RTL8723BS
pins WL_DIS# and BT_DIS#, which the data sheet vaguely says:
Shared with GPIO9 This Pin Can Externally Shutdown the RTL8723BS WLAN
function when BT_DISn is Pulled Low. When this pin deasserted, SDIO
interface will be disabled. This pin can also support the WLAN Ra
dio-off function with host interface remaining connected.
Anyway extensive testing the TheSaint on ArchLinux Arm Forum
https://archlinuxarm.org/forum/viewtopic.php?f=44&t=13064&start=120#p60548
Signed-off-by: David Summers <beagleboard@xxxxxxxxxxxxxxxxxxx>
Signed-off-by: Stefan Wahren <stefan.wahren@xxxxxxxx>
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk808 RK808_CLKOUT1>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable>;
+ reset-gpios = <&gpio4 RK_PD3 GPIO_ACTIVE_LOW>, <&gpio4 RK_PD4 GPIO_ACTIVE_LOW>;
+ };
+
+ sdio {
+ wifi_enable: wifi-enable {
+ rockchip,pins = <4 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>, <4 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/linux-rockchip
