Hi Pragnesh, Klaus,
Am Dienstag, 1. Januar 2019, 10:54:55 CET schrieb klaus.goger@xxxxxxxxxxxxxxxxxxxxx:
> > On 01.01.2019, at 09:08, <Pragnesh_Patel@xxxxxxxxxx> <Pragnesh_Patel@xxxxxxxxxx> wrote:
> >
> > From: Akash Gajjar <Akash_Gajjar@xxxxxxxxxx>
> >
> > ROCK Pi 4 is RK3399 based SBC from radxa.com. board has a 1G/2G/4G lpddr4, CSI,
> > DSI, HDMI, OTG, USB 2.0, USB 3.0, 10/100/1000 RGMII Ethernet Phy, es8316 codec,
> > POE, WIFI (for Model B only), PCIE M.2 support on board.
> >
> > This patch enables
> > - HDMI Display
> > - Console
> > - MMC, EMMC
> > - USB 2.0, USB-3.0
> > - Ethernet
> >
> > Signed-off-by: Akash Gajjar <Akash_Gajjar@xxxxxxxxxx>
> > Signed-off-by: Pragnesh Patel <Pragnesh_Patel@xxxxxxxxxx>
> > diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> > index de0c406c20cc..3fab0a3e4eeb 100644
> > --- a/arch/arm64/boot/dts/rockchip/Makefile
> > +++ b/arch/arm64/boot/dts/rockchip/Makefile
> > @@ -18,6 +18,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-scarlet-inx.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-scarlet-kd.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
> > +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rock-pi-4.dtb
>
> sort(1) would put it before roc-pc
I'd keep it were it is right now, aka after roc- and before roc960.
Otherwise we would need to resort the whole list to keep it consistent ;-)
And I really want to minimize resorts, so just keep it were it is now
and looks sorted :-D
[...]
> > + usb2 {
> > + vcc5v0_host_en: vcc5v0-host-en {
> > + rockchip,pins = <4 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
> > + };
> > + };
>
> Maybe use the GPIO bank macros here?
> 1 = RK_GPIO1, 2 = RK_GPIO2 and so forth.
Actually the other way around please :-)
Aka just use numbers for the gpio bank in new files
and the pin defines RK_PD1 for the pins.
The RK_GPIO1 -> 1, etc... defines don't really bring additional
usefulnes, so I encourage not using them in new boards.
> > +&sdmmc {
> > + bus-width = <4>;
> > + cap-mmc-highspeed;
> > + cap-sd-highspeed;
> > + cd-gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
>
> RK_PA7 for consistency.
yep, here the mapping iomux 4*8 pins <-> gpio controllers (32 pins)
is non intuitive and makes it more difficult, so the defines actually help
in following schematics.
Heiko
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/linux-rockchip
