Hi,
On Thu, May 3, 2018 at 5:10 PM, JeffyChen <jeffy.chen at rock-chips.com> wrote:
> Hi Robin,
>
>
> On 05/03/2018 08:14 PM, Robin Murphy wrote:
>>
>> On 03/05/18 04:51, JeffyChen wrote:
>>>
>>> Hi Vincente,
>>>
>>> Thanks for your mail.
>>>
>>> On 05/03/2018 03:36 AM, Vicente Bergas wrote:
>>>>
>>>> Hello,
>>>> on rk3399-sapphire there is a missing feature: the poweroff command is
>>>> unable to poweroff the system and the display stays on.
>>>> When the system is halted, power needs to be removed manually.
>>>
>>> according to the dtsi, the rk3399-sapphire is using rk808 pimc right?
>>>
>>> i think the power off flow would be:
>>> 1/ rk808 set the pm_power_off callback:
>>> drivers/mfd/rk808.c
>>> switch (rk808->variant) {
>>> case RK805_ID:
>>> ...
>>> pm_pwroff_fn = rk805_device_shutdown;
>>> ...
>>>
>>> pm_off = of_property_read_bool(np,
>>> "rockchip,system-power-controller");
>>> if (pm_off && !pm_power_off) {
>>> rk808_i2c_client = client;
>>> pm_power_off = pm_pwroff_fn;
>>> }
>>>
>>> 2/ the poweroff command would call kernel_power_off:
>>> kernel/reboot.c:
>>> void kernel_power_off(void)
>>> {
>>> ...
>>> machine_power_off();
>>> }
>>>
>>> 3/ arm64's machine_power_off() would call pm_power_off to let rk808
>>> cutoff the power.
>>
>>
>> Doesn't PSCI's pm_power_off take precedence, though? This sounds similar
>> to what my RK3328 does - I looked into that briefly a while ago, and
>> from what I remember it appeared that the firmware SYSTEM_OFF handler
>> tries to turn off the PMIC by driving the SLEEP pin, but the kernel
>> driver never actually configures it into the correct mode for that to
>> work. Thus the box just ends up spinning in the firmware until you pull
>> the plug manually.
>
>
> hmmm, right, it should be psci's power off.
>
> and i checked the BSP kernel, the rk808 driver switched to use
> pm_power_off_prepare and syscore_ops->shutdown there
>
PSCI? that is provided by the ATF (ARM Trusted Firmware), right?
The Sapphire board this issue appears on has:
1.- As first stage loader the SPL (Secondary Program Loader) from rkbin [1].
2.- As second stage loader the the ATF from rkbin [1].
3.- As third stage loader mainline u-boot.
I would strongly like to use open source and preferably mainline SPL
and ATF, but had no success when trying a few months back.
Regards,
Vicente.
[1] https://github.com/rockchip-linux/rkbin
>
>>
>>>> With Linux kernel 4.16, when reaching the halted state, the HDMI console
>>>> shows the last messages before halting.
>>>
>>> if it ends up halted, maybe something wrong during setup the
>>> pm_power_off?
>>> kernel/reboot.c:
>>> /* Instead of trying to make the power_off code look like
>>> * halt when pm_power_off is not set do it the easy way.
>>> */
>>> if ((cmd == LINUX_REBOOT_CMD_POWER_OFF) && !pm_power_off)
>>> cmd = LINUX_REBOOT_CMD_HALT;
>>>
>>>>
>>>> With 4.17.0-rc3, when reaching the halted state, the HDMI console
>>>> shows colorful static noise.
>>>>
>>> we've added a shutdown() to the iommu driver:
>>> https://patchwork.kernel.org/patch/10230817/
>>>
>>> any chance related?
>>
>>
>> For sure - the IOMMU shutdown disables paging, so if the VOP is still
>> scanning out then that will result in whatever IOVAs it was using now
>> going straight out onto the bus as physical addresses. Between the
>> RK3399 memory map and the way the IOVA allocator works, that probably
>> means it's reading from all over the peripherals region, which, er,
>> isn't ideal.
>>
>> Robin.
>>
>>
>>
>
>
