On Thu, Jan 30, 2025 at 11:08:03AM +0200, Claudiu Beznea wrote:
> Hi, Daniel,
>
> On 29.01.2025 19:24, Daniel Lezcano wrote:
> > Hi Claudiu,
> >
> > On Fri, Jan 03, 2025 at 06:38:01PM +0200, Claudiu wrote:
> >> From: Claudiu Beznea <claudiu.beznea.uj@xxxxxxxxxxxxxx>
> >>
> >> On the Renesas RZ/G3S (and other Renesas SoCs, e.g., RZ/G2{L, LC, UL}),
> >> clocks are managed through PM domains. These PM domains, registered on
> >> behalf of the clock controller driver, are configured with
> >> GENPD_FLAG_PM_CLK. In most of the Renesas drivers used by RZ SoCs, the
> >> clocks are enabled/disabled using runtime PM APIs.
> >>
> >> During probe, devices are attached to the PM domain controlling their
> >> clocks. Similarly, during removal, devices are detached from the PM domain.
> >>
> >> The detachment call stack is as follows:
> >>
> >> device_driver_detach() ->
> >> device_release_driver_internal() ->
> >> __device_release_driver() ->
> >> device_remove() ->
> >> platform_remove() ->
> >> dev_pm_domain_detach()
> >>
> >> In the upcoming Renesas RZ/G3S thermal driver, the
> >> struct thermal_zone_device_ops::change_mode API is implemented to
> >> start/stop the thermal sensor unit. Register settings are updated within
> >> the change_mode API.
> >>
> >> In case devres helpers are used for thermal zone register/unregister the
> >> struct thermal_zone_device_ops::change_mode API is invoked when the
> >> driver is unbound. The identified call stack is as follows:
> >>
> >> device_driver_detach() ->
> >> device_release_driver_internal() ->
> >> device_unbind_cleanup() ->
> >> devres_release_all() ->
> >> devm_thermal_of_zone_release() ->
> >> thermal_zone_device_disable() ->
> >> thermal_zone_device_set_mode() ->
> >> rzg3s_thermal_change_mode()
> >>
> >> The device_unbind_cleanup() function is called after the thermal device is
> >> detached from the PM domain (via dev_pm_domain_detach()).
> >>
> >> The rzg3s_thermal_change_mode() implementation calls
> >> pm_runtime_resume_and_get()/pm_runtime_put_autosuspend() before/after
> >> accessing the registers. However, during the unbind scenario, the
> >> devm_thermal_of_zone_release() is invoked after dev_pm_domain_detach().
> >> Consequently, the clocks are not enabled, as the device is removed from
> >> the PM domain at this time, leading to an Asynchronous SError Interrupt.
> >> The system cannot be used after this.
> >
> > I've been through the driver before responding to this change. What is the
> > benefit of powering down / up (or clock off / on) the thermal sensor when
> > reading the temperature ?
> >
> > I can understand for disable / enable but I don't get for the classic usage
> > where a governor will be reading the temperature regularly.
>
> I tried to be as power saving as possible both at runtime and after the IP
> is not used anymore as the HW manual doesn't mentioned anything about
> accuracy or implications of disabling the IP clock at runtime. We use
> similar approach (of disabling clocks at runtime) for other IPs in the
> RZ/G3S SoC as well.
>
> >
> > Would the IP need some cycles to capture the temperature accurately after the
> > clock is enabled ?
>
> There is nothing about this mentioned about this in the HW manual of the
> RZ/G3S SoC. The only points mentioned are as described in the driver code:
> - wait at least 3us after each IIO channel read
> - wait at least 30us after enabling the sensor
> - wait at least 50us after setting OE bit in TSU_SM
>
> For this I chose to have it implemented as proposed.
IMO, disabling/enabling the clock between two reads through the pm runtime may
not be a good thing, especially if the system enters a thermal situation where
it has to mitigate.
Without any testing capturing the temperatures and compare between the always-on
and on/off, it is hard to say if it is true or not. Up to you to test that or
not. If you think it is fine, then let's go with it.
> If any, the HW manual is available here
> https://www.renesas.com/en/document/mah/rzg3s-group-users-manual-hardware?r=25458591
> (an archive is here; the manual is in Deliverables/r01uh1014ej0110-rzg3s.pdf)
>
> Thank you for your review,
> Claudiu
>
> >
> >> Add thermal_of_zone_register()/thermal_of_zone_unregister(). These will
> >> be used in the upcomming RZ/G3S thermal driver.
> >>
> >> Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@xxxxxxxxxxxxxx>
>
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
