Hello,
This series enables auto negotiation for the mv88q2110 device.
Previously this feature have been disabled for mv88q2110, while enabled
for other devices supported by this driver.
The initial driver implementation states this is due to the
configuration sequence provided by the vendor did not work. By comparing
the initialization sequence of other devices this driver supports and
the out-of-tree PHY driver for mv88q2110 found in the Renesas BSP [1] I
was able to figure out a working configuration.
As I have no access to the datasheets of either of these devices it
would be super if someone who has could sanity check the initialization
sequence.
With this series I'm able to auto negotiate both 1000Mbps and 100Mbps
links without issue.
# ethtool eth0
Settings for eth0:
Supported ports: [ ]
Supported link modes: 100baseT1/Full
1000baseT1/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 100baseT1/Full
1000baseT1/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 100baseT1/Full
1000baseT1/Full
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: on
master-slave cfg: preferred master
master-slave status: slave
Port: Twisted Pair
PHYAD: 0
Transceiver: external
MDI-X: Unknown
Link detected: yes
SQI: 15/15
And the performance is good too. Without this change I was not able to
manually configure a 1000Mbps link, only 100Mbps ones. So this gives a
huge performance boost for my use-case.
[ 5] local 10.1.0.2 port 5201 connected to 10.1.0.1 port 38346
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 96.8 MBytes 812 Mbits/sec 0 469 KBytes
[ 5] 1.00-2.00 sec 94.3 MBytes 791 Mbits/sec 0 469 KBytes
[ 5] 2.00-3.00 sec 96.1 MBytes 806 Mbits/sec 0 469 KBytes
[ 5] 3.00-4.00 sec 98.3 MBytes 825 Mbits/sec 0 469 KBytes
[ 5] 4.00-5.00 sec 98.4 MBytes 825 Mbits/sec 0 469 KBytes
[ 5] 5.00-6.00 sec 98.4 MBytes 826 Mbits/sec 0 469 KBytes
[ 5] 6.00-7.00 sec 98.9 MBytes 830 Mbits/sec 0 469 KBytes
[ 5] 7.00-8.00 sec 91.7 MBytes 769 Mbits/sec 0 469 KBytes
[ 5] 8.00-9.00 sec 99.4 MBytes 834 Mbits/sec 0 747 KBytes
[ 5] 9.00-10.00 sec 101 MBytes 851 Mbits/sec 0 747 KBytes
Patch 1/3 and 2/3 are preparation patches that align and move functions
around as the mv88q2110 code paths can now reuses much of what is done
for mv88q2220. While patch 3/3 adds the new initialization sequence and
removes the auto negotiation limit for mv88q2110.
1. https://github.com/renesas-rcar/linux-bsp/commit/2a1f07d0e722a18188cfe62842b61f2fbc0ba812
Niklas Söderlund (3):
net: phy: marvell-88q2xxx: Align soft reset for mv88q2110 and
mv88q2220
net: phy: marvell-88q2xxx: Make register writer function generic
net: phy: marvell-88q2xxx: Enable auto negotiation for mv88q2110
drivers/net/phy/marvell-88q2xxx.c | 124 +++++++++++++++++-------------
1 file changed, 71 insertions(+), 53 deletions(-)
--
2.46.2
