Hi Serge Semin,
> -----Original Message-----
> From: Serge Semin <fancer.lancer@xxxxxxxxx>
> Sent: Friday, August 23, 2024 10:11 AM
> Subject: Re: [net-next v2 2/9] net: stmmac: platform: Convert to devm_clk_get_enabled() and
> devm_clk_get_optional_enabled()
>
> Hi Yangtao
>
> On Fri, Aug 23, 2024 at 01:21:14AM -0600, Yangtao Li wrote:
> > Use devm_clk_get_enabled() and devm_clk_get_optional_enabled() to
> > simplify code.
> >
> > Signed-off-by: Yangtao Li <frank.li@xxxxxxxx>
> > Reviewed-by: Maxime Chevallier <maxime.chevallier@xxxxxxxxxxx>
> > ---
> > v2:
> > -remove unused 'ret'
> > -fix incompatible-pointer-types
> >
> > .../ethernet/stmicro/stmmac/stmmac_platform.c | 35
> > +++++--------------
> > 1 file changed, 8 insertions(+), 27 deletions(-)
> >
> > diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
> > b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
> > index ad868e8d195d..1a66baaa4081 100644
> > --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
> > +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
> > @@ -415,8 +415,6 @@ static int stmmac_of_get_mac_mode(struct
> > device_node *np) static void stmmac_remove_config_dt(struct platform_device *pdev,
> > struct plat_stmmacenet_data *plat) {
> > - clk_disable_unprepare(plat->stmmac_clk);
> > - clk_disable_unprepare(plat->pclk);
> > of_node_put(plat->phy_node);
> > of_node_put(plat->mdio_node);
> > }
> > @@ -436,7 +434,6 @@ stmmac_probe_config_dt(struct platform_device *pdev, u8 *mac)
> > struct plat_stmmacenet_data *plat;
> > struct stmmac_dma_cfg *dma_cfg;
> > int phy_mode;
> > - void *ret;
> > int rc;
> >
> > plat = devm_kzalloc(&pdev->dev, sizeof(*plat), GFP_KERNEL); @@
> > -615,21 +612,16 @@ stmmac_probe_config_dt(struct platform_device
> > *pdev, u8 *mac)
> >
> > /* clock setup */
> > if (!of_device_is_compatible(np, "snps,dwc-qos-ethernet-4.10")) {
> > - plat->stmmac_clk = devm_clk_get(&pdev->dev,
> > - STMMAC_RESOURCE_NAME);
> > + plat->stmmac_clk = devm_clk_get_enabled(&pdev->dev,
> > +STMMAC_RESOURCE_NAME);
> > if (IS_ERR(plat->stmmac_clk)) {
> > dev_warn(&pdev->dev, "Cannot get CSR clock\n");
> > plat->stmmac_clk = NULL;
> > }
> > - clk_prepare_enable(plat->stmmac_clk);
> > }
> >
> > - plat->pclk = devm_clk_get_optional(&pdev->dev, "pclk");
> > - if (IS_ERR(plat->pclk)) {
> > - ret = plat->pclk;
> > - goto error_pclk_get;
> > - }
> > - clk_prepare_enable(plat->pclk);
> > + plat->pclk = devm_clk_get_optional_enabled(&pdev->dev, "pclk");
> > + if (IS_ERR(plat->pclk))
>
> > + return (void *)plat->pclk;
>
> Use the ERR_CAST() macro instead of the open coded void type cast.
Which is better ERR_PTR or ERR_CAST in this case?
Cheers,
Biju
>
> >
> > /* Fall-back to main clock in case of no PTP ref is passed */
> > plat->clk_ptp_ref = devm_clk_get(&pdev->dev, "ptp_ref"); @@ -644,26
> > +636,15 @@ stmmac_probe_config_dt(struct platform_device *pdev, u8
> > *mac)
> >
> > plat->stmmac_rst = devm_reset_control_get_optional(&pdev->dev,
> > STMMAC_RESOURCE_NAME);
> > - if (IS_ERR(plat->stmmac_rst)) {
> > - ret = plat->stmmac_rst;
> > - goto error_hw_init;
> > - }
> > + if (IS_ERR(plat->stmmac_rst))
>
> > + return (void *)plat->stmmac_rst;
>
> ditto
>
> >
> > plat->stmmac_ahb_rst = devm_reset_control_get_optional_shared(
> > &pdev->dev, "ahb");
> > - if (IS_ERR(plat->stmmac_ahb_rst)) {
> > - ret = plat->stmmac_ahb_rst;
> > - goto error_hw_init;
> > - }
> > + if (IS_ERR(plat->stmmac_ahb_rst))
>
> > + return (void *)plat->stmmac_ahb_rst;
>
> ditto
>
> -Serge(y)
>
> >
> > return plat;
> > -
> > -error_hw_init:
> > - clk_disable_unprepare(plat->pclk);
> > -error_pclk_get:
> > - clk_disable_unprepare(plat->stmmac_clk);
> > -
> > - return ret;
> > }
> >
> > static void devm_stmmac_remove_config_dt(void *data)
> > --
> > 2.39.0
> >
> >
