Re: [PATCH v2 09/12] i2c: riic: Add support for fast mode plus

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi, Geert, all,

On 28.06.2024 12:22, Geert Uytterhoeven wrote:
> Hi Claudiu,
> 
> On Tue, Jun 25, 2024 at 2:14 PM Claudiu <claudiu.beznea@xxxxxxxxx> wrote:
>> From: Claudiu Beznea <claudiu.beznea.uj@xxxxxxxxxxxxxx>
>>
>> Fast mode plus is available on most of the IP variants that RIIC driver
>> is working with. The exception is (according to HW manuals of the SoCs
>> where this IP is available) the Renesas RZ/A1H. For this, patch
>> introduces the struct riic_of_data::fast_mode_plus.
>>
>> Fast mode plus was tested on RZ/G3S, RZ/G2{L,UL,LC}, RZ/Five by
>> instantiating the RIIC frequency to 1MHz and issuing i2c reads on the
>> fast mode plus capable devices (and the i2c clock frequency was checked on
>> RZ/G3S).
>>
>> Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@xxxxxxxxxxxxxx>
> 
> Thanks for your patch!
> 
>> --- a/drivers/i2c/busses/i2c-riic.c
>> +++ b/drivers/i2c/busses/i2c-riic.c
>> @@ -407,6 +413,9 @@ static int riic_init_hw(struct riic_dev *riic)
>>         riic_writeb(riic, 0, RIIC_ICSER);
>>         riic_writeb(riic, ICMR3_ACKWP | ICMR3_RDRFS, RIIC_ICMR3);
>>
>> +       if (info->fast_mode_plus && t->bus_freq_hz == I2C_MAX_FAST_MODE_PLUS_FREQ)
>> +               riic_clear_set_bit(riic, 0, ICFER_FMPE, RIIC_ICFER);
> 
> Unless FM+ is specified, RIIC_ICFER is never written to.
> Probably the register should always be initialized, also to make sure
> the FMPE bit is cleared when it was set by the boot loader, but FM+
> is not to be used.

Instead of clearing only this bit, what do you think about using
reset_control_reset() instead of reset_control_deassert() in riic_i2c_probe()?

HW manuals for all the devices listed in
Documentation/devicetree/bindings/i2c/renesas,riic.yaml specifies that
ICFER_FMPE register is initialized with a default value by reset. All the
other registers are initialized with default values at reset (according to
HW manuals). I've checked it on RZ/G3S and it behaves like this.

With this:

diff --git a/drivers/i2c/busses/i2c-riic.c b/drivers/i2c/busses/i2c-riic.c
index ba969ad5f015..150e7841f178 100644
--- a/drivers/i2c/busses/i2c-riic.c
+++ b/drivers/i2c/busses/i2c-riic.c
@@ -457,7 +457,7 @@ static int riic_i2c_probe(struct platform_device *pdev)
                return dev_err_probe(dev, PTR_ERR(riic->rstc),
                                     "Error: missing reset ctrl\n");

-       ret = reset_control_deassert(riic->rstc);
+       ret = reset_control_reset(riic->rstc);
        if (ret)
                return ret;

I've did basic tests (i2cdetect + i2cget with FM+ frequency) on RZ/G2{L,
LC, UL}, RZ/V2L and all was good.

Thank you,
Claudiu Beznea

> 
> 
>> +
>>         riic_clear_set_bit(riic, ICCR1_IICRST, 0, RIIC_ICCR1);
>>
>>         pm_runtime_mark_last_busy(dev);
> 
> Gr{oetje,eeting}s,
> 
>                         Geert
> 




[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux