Re: [PATCH v3 01/15] dt-bindings: pinctrl: renesas: Document RZ/V2H(P) SoC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, May 30, 2024 at 06:38:43PM +0100, Prabhakar wrote:
> From: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> 
> Add documentation for the pin controller found on the Renesas RZ/V2H(P)
> (R9A09G057) SoC. The RZ/V2H PFC varies slightly compared to the RZ/G2L
> family:
> - Additional bits need to be set during pinmuxing.
> - The GPIO pin count is different.
> 
> Hence, a SoC-specific compatible string, 'renesas,r9a09g057-pinctrl', is
> added for the RZ/V2H(P) SoC.
> 
> Also, add the 'renesas,output-impedance' property. The drive strength
> setting on RZ/V2H(P) depends on the different power rails coming out from
> the PMIC (connected via I2C). These power rails (required for drive
> strength) can be 1.2V, 1.8V, or 3.3V.
> 
> Pins are grouped into 4 groups:
> 
> Group 1: Impedance
> - 150/75/38/25 ohms (at 3.3V)
> - 130/65/33/22 ohms (at 1.8V)
> 
> Group 2: Impedance
> - 50/40/33/25 ohms (at 1.8V)
> 
> Group 3: Impedance
> - 150/75/37.5/25 ohms (at 3.3V)
> - 130/65/33/22 ohms (at 1.8V)
> 
> Group 4: Impedance
> - 110/55/30/20 ohms (at 1.8V)
> - 150/75/38/25 ohms (at 1.2V)
> 
> The 'renesas,output-impedance' property, as documented, can be
> [0, 1, 2, 3], these correspond to register bit values that can
> be set in the PFC_IOLH_mn register, which adjusts the drive
> strength value and is pin-dependent.
> 
> As power rail information may not be available very early in the boot
> process, the 'renesas,output-impedance' property is added instead of
> reusing the 'output-impedance-ohms' property.
> 
> Also, allow bias-disable, bias-pull-down and bias-pull-up properties
> as these can be used to configure the pins.
> 
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> ---
> v2->v3
> - Updated description for renesas,output-impedance property
> - Updated commit description
> 
> RFC->v2
> - Renamed renesas-rzv2h,output-impedance -> renesas,output-impedance
> - Updated values for renesas,output-impedance
> - Added bias properties
> ---
>  .../pinctrl/renesas,rzg2l-pinctrl.yaml        | 23 +++++++++++++++----
>  1 file changed, 19 insertions(+), 4 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml
> index 881e992adca3..957b9f7e7de5 100644
> --- a/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml
> +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml
> @@ -26,6 +26,7 @@ properties:
>                - renesas,r9a07g043-pinctrl # RZ/G2UL{Type-1,Type-2} and RZ/Five
>                - renesas,r9a07g044-pinctrl # RZ/G2{L,LC}
>                - renesas,r9a08g045-pinctrl # RZ/G3S
> +              - renesas,r9a09g057-pinctrl # RZ/V2H(P)
>  
>        - items:
>            - enum:
> @@ -66,10 +67,14 @@ properties:
>      maxItems: 1
>  
>    resets:
> -    items:
> -      - description: GPIO_RSTN signal
> -      - description: GPIO_PORT_RESETN signal
> -      - description: GPIO_SPARE_RESETN signal
> +    oneOf:
> +      - items:
> +          - description: GPIO_RSTN signal
> +          - description: GPIO_PORT_RESETN signal
> +          - description: GPIO_SPARE_RESETN signal
> +      - items:
> +          - description: PFC main reset
> +          - description: Reset for the control register related to WDTUDFCA and WDTUDFFCM pins

You need a conditional schema for ensuring the length is 2 for RZ/V2H 
and 3 otherwise.

>  
>  additionalProperties:
>    anyOf:
> @@ -111,6 +116,16 @@ additionalProperties:
>          output-high: true
>          output-low: true
>          line-name: true
> +        bias-disable: true
> +        bias-pull-down: true
> +        bias-pull-up: true
> +        renesas,output-impedance:
> +          description: |

Don't need '|'.

> +            Output impedance for pins on the RZ/V2H(P) SoC. Values 0, 1, 2, and 3

Don't repeat values in free form text.

> +            correspond to register bit values that can be set in the PFC_IOLH_mn
> +            register, which adjusts the drive strength value and is pin-dependent.
> +          $ref: /schemas/types.yaml#/definitions/uint32
> +          enum: [0, 1, 2, 3]
>  
>      - type: object
>        additionalProperties:
> -- 
> 2.34.1
> 




[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux