From: Claudiu Beznea <claudiu.beznea.uj@xxxxxxxxxxxxxx>
Hi,
Series adds support for power domains on rzg2l driver.
RZ/G2L kind of devices support a functionality called MSTOP (module
stop/standby). According to hardware manual the module could be switch
to standby after its clocks are disabled. The reverse order of operation
should be done when enabling a module (get the module out of standby,
enable its clocks etc).
In [1] the MSTOP settings were implemented by adding code in driver
to attach the MSTOP state to the IP clocks. But it has been proposed
to implement it as power domain. The result is this series.
The DT bindings were updated with power domain IDs (plain integers
that matches the DT with driver data structures). The current DT
bindings were updated with module IDs for the modules listed in tables
with name "Registers for Module Standby Mode" (see HW manual) exception
being RZ/G3S where, due to the power down functionality, the DDR,
TZCDDR, OTFDE_DDR were also added.
Domain IDs were added to all SoC specific bindings.
Thank you,
Claudiu Beznea
Changes in v4:
- dropped the pwrdn functionality until it is better understanded
- dropped patch "clk: renesas: rzg2l-cpg: Add suspend/resume
support for power domains" from v3; this will be replaced
by propertly calling device_set_wakup_path() in serial console
driver
- instantiated the watchdog domain in r8a08g045 clock driver; this
allow applying r9a08g045 clock patch w/o affecting watchdog and later,
after all good with watchdog patches series at [2], only patch
"arm64: dts: renesas: r9a08g045: Update #power-domain-cells = <1>"
will need to be applied
Changes in v3:
- collected tags
- dinamically detect if a SCIF is serial console and populate
pd->suspend_check
- dropped patch 09/10 from v2
Changes in v2:
- addressed review comments
- dropped:
- dt-bindings: clock: r9a09g011-cpg: Add always-on power domain IDs
- clk: renesas: r9a07g043: Add initial support for power domains
- clk: renesas: r9a07g044: Add initial support for power domains
- clk: renesas: r9a09g011: Add initial support for power domains
- clk: renesas: r9a09g011: Add initial support for power domains
- arm64: dts: renesas: r9a07g043: Update #power-domain-cells = <1>
- arm64: dts: renesas: r9a07g044: Update #power-domain-cells = <1>
- arm64: dts: renesas: r9a07g054: Update #power-domain-cells = <1>
- arm64: dts: renesas: r9a09g011: Update #power-domain-cells = <1>
as suggested in the review process
- dropped "arm64: dts: renesas: rzg3s-smarc-som: Guard the ethernet IRQ
GPIOs with proper flags" patch as it was integrated
- added suspend to RAM support
- collected tag
[1] https://lore.kernel.org/all/20231120070024.4079344-4-claudiu.beznea.uj@xxxxxxxxxxxxxx/
[2] https://lore.kernel.org/all/20240410134044.2138310-1-claudiu.beznea.uj@xxxxxxxxxxxxxx/
Claudiu Beznea (8):
dt-bindings: clock: r9a07g043-cpg: Add power domain IDs
dt-bindings: clock: r9a07g044-cpg: Add power domain IDs
dt-bindings: clock: r9a07g054-cpg: Add power domain IDs
dt-bindings: clock: r9a08g045-cpg: Add power domain IDs
dt-bindings: clock: renesas,rzg2l-cpg: Update #power-domain-cells =
<1> for RZ/G3S
clk: renesas: rzg2l: Extend power domain support
clk: renesas: r9a08g045: Add support for power domains
arm64: dts: renesas: r9a08g045: Update #power-domain-cells = <1>
.../bindings/clock/renesas,rzg2l-cpg.yaml | 18 +-
arch/arm64/boot/dts/renesas/r9a08g045.dtsi | 20 +-
drivers/clk/renesas/r9a08g045-cpg.c | 41 ++++
drivers/clk/renesas/rzg2l-cpg.c | 199 ++++++++++++++++--
drivers/clk/renesas/rzg2l-cpg.h | 67 ++++++
include/dt-bindings/clock/r9a07g043-cpg.h | 52 +++++
include/dt-bindings/clock/r9a07g044-cpg.h | 58 +++++
include/dt-bindings/clock/r9a07g054-cpg.h | 58 +++++
include/dt-bindings/clock/r9a08g045-cpg.h | 70 ++++++
9 files changed, 558 insertions(+), 25 deletions(-)
--
2.39.2
