[PATCH RESEND net-next v6 5/7] net: stmmac: Signal to PHY/PCS drivers to keep RX clock on

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



There is a reocurring issue with stmmac controllers where the MAC fails to
initialize its hardware if an RX clock signal isn't provided on the MAC/PHY
link.

This causes issues when PHY or PCS devices either go into suspend while
cutting the RX clock or do not bring the clock signal up early enough for
the MAC to initialize successfully.

Set the mac_requires_rxc flag in the stmmac phylink config so that PHY/PCS
drivers know to keep the RX clock up at all times.

Reported-by: Clark Wang <xiaoning.wang@xxxxxxx>
Link: https://lore.kernel.org/all/20230202081559.3553637-1-xiaoning.wang@xxxxxxx/
Reported-by: Clément Léger <clement.leger@xxxxxxxxxxx>
Link: https://lore.kernel.org/linux-arm-kernel/20230116103926.276869-4-clement.leger@xxxxxxxxxxx/
Co-developed-by: Russell King (Oracle) <rmk+kernel@xxxxxxxxxxxxxxx>
Signed-off-by: Russell King (Oracle) <rmk+kernel@xxxxxxxxxxxxxxx>
Signed-off-by: Romain Gantois <romain.gantois@xxxxxxxxxxx>
Reviewed-by: Andrew Lunn <andrew@xxxxxxx>
---
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 79844dbe4258..2290f4808d7e 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -1218,6 +1218,9 @@ static int stmmac_phy_setup(struct stmmac_priv *priv)
 	priv->phylink_config.type = PHYLINK_NETDEV;
 	priv->phylink_config.mac_managed_pm = true;
 
+	/* Stmmac always requires an RX clock for hardware initialization */
+	priv->phylink_config.mac_requires_rxc = true;
+
 	mdio_bus_data = priv->plat->mdio_bus_data;
 	if (mdio_bus_data)
 		priv->phylink_config.ovr_an_inband =
@@ -3408,6 +3411,10 @@ static int stmmac_hw_setup(struct net_device *dev, bool ptp_register)
 	u32 chan;
 	int ret;
 
+	/* Make sure RX clock is enabled */
+	if (priv->hw->phylink_pcs)
+		phylink_pcs_pre_init(priv->phylink, priv->hw->phylink_pcs);
+
 	/* DMA initialization and SW reset */
 	ret = stmmac_init_dma_engine(priv);
 	if (ret < 0) {

-- 
2.44.0





[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux