[PATCH] arm64: dts: renesas: white-hawk: ethernet: Describe adv1 and avb2

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Describe the two Marvel 88Q2110/QFN40 PHYs available on the R-Car V4H
White Hawk RAVB/Ethernet(1000Base-T1) sub-board. The two PHYs are wired
up on the board by default, there is no need to move any resistors which
are needed to access other PHYs available on this sub-board.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@xxxxxxxxxxxx>
---
Hello Geert,

This patch depends on the update to the bindings posted in [1] to not
fail DT validation check's. However with this change I can bind to the
two PHYs without having to touch ether the PHY or RAVB drivers, the MDIO
core handle the reset of the MDIO bus.

1. [PACH] dt-bindings: net: renesas,etheravb: Add MDIO bus reset properties
---
 .../renesas/r8a779g0-white-hawk-ethernet.dtsi | 74 +++++++++++++++++++
 1 file changed, 74 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk-ethernet.dtsi b/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk-ethernet.dtsi
index 4f411f95c674..63e0fdae4ff6 100644
--- a/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk-ethernet.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk-ethernet.dtsi
@@ -6,6 +6,38 @@
  * Copyright (C) 2022 Glider bv
  */
 
+&avb1 {
+	pinctrl-0 = <&avb1_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&phy1>;
+	status = "okay";
+	reset-gpios = <&gpio6 1 GPIO_ACTIVE_LOW>;
+	reset-post-delay-us = <4000>;
+
+	phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <0>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&avb2 {
+	pinctrl-0 = <&avb2_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&phy2>;
+	status = "okay";
+	reset-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>;
+	reset-post-delay-us = <4000>;
+
+	phy2: ethernet-phy@2 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <0>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
 &i2c0 {
 	eeprom@53 {
 		compatible = "rohm,br24g01", "atmel,24c01";
@@ -14,3 +46,45 @@ eeprom@53 {
 		pagesize = <8>;
 	};
 };
+
+&pfc {
+	avb1_pins: avb1 {
+		mux {
+			groups = "avb1_link", "avb1_mdio", "avb1_rgmii",
+				 "avb1_txcrefclk";
+			function = "avb1";
+		};
+
+		pins_mdio {
+			groups = "avb1_mdio";
+			drive-strength = <24>;
+			bias-disable;
+		};
+
+		pins_mii {
+			groups = "avb1_rgmii";
+			drive-strength = <24>;
+			bias-disable;
+		};
+	};
+
+	avb2_pins: avb2 {
+		mux {
+			groups = "avb2_link", "avb2_mdio", "avb2_rgmii",
+				 "avb2_txcrefclk";
+			function = "avb2";
+		};
+
+		pins_mdio {
+			groups = "avb2_mdio";
+			drive-strength = <24>;
+			bias-disable;
+		};
+
+		pins_mii {
+			groups = "avb2_rgmii";
+			drive-strength = <24>;
+			bias-disable;
+		};
+	};
+};
-- 
2.44.0





[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux