Re: [DO NOT MERGE v6 12/37] dt-bindings: pci: pci-sh7751: Add SH7751 PCI

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Jan 09, 2024 at 01:42:53PM +0100, Linus Walleij wrote:
> Hi Yoshinori,
> 
> thanks for your patch!
> 
> On Tue, Jan 9, 2024 at 9:24 AM Yoshinori Sato
> <ysato@xxxxxxxxxxxxxxxxxxxx> wrote:
> 
> > Renesas SH7751 PCI Controller json-schema.
> >
> > Signed-off-by: Yoshinori Sato <ysato@xxxxxxxxxxxxxxxxxxxx>
> (...)
> > +  renesas,bus-arbit-round-robin:
> > +    $ref: /schemas/types.yaml#/definitions/flag
> > +    description: |
> > +      Set DMA bus arbitration to round robin.
> > +
> > +  pci-command-reg-fast-back-to-back:
> > +    $ref: /schemas/types.yaml#/definitions/flag
> > +    description: |
> > +      Set for PCI command register Fast Back-to-Back enable bit.
> > +
> > +  pci-command-reg-serr:
> > +    $ref: /schemas/types.yaml#/definitions/flag
> > +    description: |
> > +      Set for PCI command register SERR# enable.
> > +
> > +  pci-command-reg-wait-cycle-control:
> > +    $ref: /schemas/types.yaml#/definitions/flag
> > +    description: |
> > +      Set for PCI command register Wait cycle control bit.
> > +
> > +  pci-command-reg-parity-error-response:
> > +    $ref: /schemas/types.yaml#/definitions/flag
> > +    description: |
> > +      Set for PCI Command register Parity error response bit.
> > +
> > +  pci-command-reg-vga-snoop:
> > +    $ref: /schemas/types.yaml#/definitions/flag
> > +    description: |
> > +      Set for PCI Command register VGA palette snoop bit.
> > +
> > +  pci-command-reg-write-invalidate:
> > +    $ref: /schemas/types.yaml#/definitions/flag
> > +    description: |
> > +      Set for PCI Command register Memory write and invaldate enable bit.
> > +
> > +  pci-command-reg-special-cycle:
> > +    $ref: /schemas/types.yaml#/definitions/flag
> > +    description: |
> > +      Set for PCI Command register Special cycle bit.
> > +
> > +  pci-command-reg-bus-master:
> > +    $ref: /schemas/types.yaml#/definitions/flag
> > +    description: |
> > +      Set for PCI Command register Bus master bit.
> > +
> > +  pci-command-reg-memory-space:
> > +    $ref: /schemas/types.yaml#/definitions/flag
> > +    description: |
> > +      Set for PCI Command register Memory space bit.
> > +
> > +  pci-command-reg-io-space:
> > +    $ref: /schemas/types.yaml#/definitions/flag
> > +    description: |
> > +      Set for PCI Command register I/O space bit.
> 
> Do you really need to configure all these things? It seems they are
> just set to default values anyway?
> 
> Can't you just look at the compatible "renesas,sh7751-pci" and
> set it to the values you know are needed for that compatible?

Yes. Please drop all these.

> 
> > +  pci-bar:
> > +    $ref: /schemas/types.yaml#/definitions/uint32-matrix
> > +    description: Overwrite to  PCI CONFIG Base Address Registers value.
> > +    items:
> > +      items:
> > +        - description: BAR register number
> > +        - description: BAR register value
> > +    minItems: 1
> > +    maxItems: 6
> 
> Same with this, isn't this always the same (hardcoded) values
> for "renesas,sh7751-pci" if used?

The OpenFirmware PCI bus supplement already defines how to specify BAR 
values in DT in "reg" or "assigned-addresses". If you need to specify 
these, use that. Note don't expect the kernel to do anything with them.

Rob

> 
> > +            interrupt-map = <0x0000 0 0 1 &julianintc 5>,
> > +                            <0x0000 0 0 2 &julianintc 6>,
> > +                            <0x0000 0 0 3 &julianintc 7>,
> > +                            <0x0000 0 0 4 &julianintc 8>,
> > +                            <0x0800 0 0 1 &julianintc 6>,
> > +                            <0x0800 0 0 2 &julianintc 7>,
> > +                            <0x0800 0 0 3 &julianintc 8>,
> > +                            <0x0800 0 0 4 &julianintc 5>,
> > +                            <0x1000 0 0 1 &julianintc 7>,
> > +                            <0x1000 0 0 2 &julianintc 8>,
> > +                            <0x1000 0 0 3 &julianintc 5>,
> > +                            <0x1000 0 0 4 &julianintc 6>;
> 
> This interrupt-map looks very strange, usually the last cell is the polarity
> flag and here it is omitted? I would expect something like:
> 
> <0x0000 0 0 1 &julianintc 5 IRQ_TYPE_LEVEL_LOW>, (...)
> 
> The interrupt-map schema in dtschema isn't really looking at this
> so it is easy to get it wrong.

dtc should IIRC. Maybe not in the example being incomplete.

Rob





[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux