Re: [PATCH RFT 2/2] i2c: rcar: improve accuracy for R-Car Gen3+

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Wolfram,

On Wed, Sep 13, 2023 at 11:38 AM Wolfram Sang
<wsa+renesas@xxxxxxxxxxxxxxxxxxxx> wrote:
> With some new registers, SCL can be calculated to be closer to the
> desired rate. Apply the new formula for R-Car Gen3 device types.
>
> Signed-off-by: Wolfram Sang <wsa+renesas@xxxxxxxxxxxxxxxxxxxx>

Thanks for your patch!

> --- a/drivers/i2c/busses/i2c-rcar.c
> +++ b/drivers/i2c/busses/i2c-rcar.c

> @@ -84,11 +88,25 @@
>  #define RMDMAE BIT(1)  /* DMA Master Received Enable */
>  #define TMDMAE BIT(0)  /* DMA Master Transmitted Enable */
>
> +/* ICCCR2 */
> +#define CDFD   BIT(2)  /* CDF Disable */
> +#define HLSE   BIT(1)  /* HIGH/LOW Separate Control Enable */
> +#define SME    BIT(0)  /* SCL Mask Enable */
> +
>  /* ICFBSCR */
>  #define TCYC17 0x0f            /* 17*Tcyc delay 1st bit between SDA and SCL */
>
>  #define RCAR_MIN_DMA_LEN       8
>
> +/* SCL low/high ratio 5:4 to meet all I2C timing specs (incl safety margin) */
> +#define RCAR_SCLD_RATIO                5
> +#define RCAR_SCHD_RATIO                4
> +/*
> + * SMD should be smaller than SCLD/SCHD and is always around 20 in the docs.
> + * Thus, we simply use 20 which works for low and high speeds.
> +*/

(checkpatch) WARNING: Block comments should align the * on each line

> +#define RCAR_DEFAULT_SMD       20
> +
>  #define RCAR_BUS_PHASE_START   (MDBS | MIE | ESG)
>  #define RCAR_BUS_PHASE_DATA    (MDBS | MIE)
>  #define RCAR_BUS_PHASE_STOP    (MDBS | MIE | FSB)

> @@ -301,24 +316,57 @@ static int rcar_i2c_clock_calculate(struct rcar_i2c_priv *priv)
>         round = DIV_ROUND_CLOSEST(ick, 1000000);
>         round = DIV_ROUND_CLOSEST(round * sum, 1000);
>
> -       /*
> -        * SCL  = ick / (20 + 8 * SCGD + F[(ticf + tr + intd) * ick])
> -        * 20 + 8 * SCGD + F[...] = ick / SCL
> -        * SCGD = ((ick / SCL) - 20 - F[...]) / 8
> -        * Result (= SCL) should be less than bus_speed for hardware safety
> -        */
> -       scgd = DIV_ROUND_UP(ick, t.bus_freq_hz ?: 1);
> -       scgd = DIV_ROUND_UP(scgd - 20 - round, 8);
> -       scl = ick / (20 + 8 * scgd + round);
> +       if (priv->devtype < I2C_RCAR_GEN3) {
> +               u32 scgd;
> +               /*
> +                * SCL  = ick / (20 + 8 * SCGD + F[(ticf + tr + intd) * ick])
> +                * 20 + 8 * SCGD + F[...] = ick / SCL
> +                * SCGD = ((ick / SCL) - 20 - F[...]) / 8
> +                * Result (= SCL) should be less than bus_speed for hardware safety
> +                */
> +               scgd = DIV_ROUND_UP(ick, t.bus_freq_hz ?: 1);
> +               scgd = DIV_ROUND_UP(scgd - 20 - round, 8);
> +               scl = ick / (20 + 8 * scgd + round);
>
> -       if (scgd > 0x3f)
> -               goto err_no_val;
> +               if (scgd > 0x3f)
> +                       goto err_no_val;
>
> -       dev_dbg(dev, "clk %u/%u(%lu), round %u, CDF: %u, SCGD: %u\n",
> -               scl, t.bus_freq_hz, rate, round, cdf, scgd);
> +               dev_dbg(dev, "clk %u/%u(%lu), round %u, CDF: %u, SCGD: %u\n",
> +                       scl, t.bus_freq_hz, rate, round, cdf, scgd);
>
> -       /* keep icccr value */
> -       priv->icccr = scgd << cdf_width | cdf;
> +               priv->icccr = scgd << cdf_width | cdf;
> +       } else {
> +               u32 x, sum_ratio = RCAR_SCHD_RATIO + RCAR_SCLD_RATIO;
> +               /*
> +                * SCLD/SCHD ratio and SMD default value are explained above
> +                * where they are defined. With these definitions, we can compute
> +                * x as a base value for the SCLD/SCHD ratio:
> +                *
> +                * SCL = clkp / (8 + 2 * SMD + SCLD + SCHD + F[(ticf + tr + intd) * clkp])
> +                * SCL = clkp / (8 + 2 * RCAR_DEFAULT_SMD + RCAR_SCLD_RATIO * x
> +                *               + RCAR_SCHD_RATIO * x + F[...])

(checkpatch) WARNING: please, no space before tabs

I hope to give this a full test-run on my farm soon...

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds



[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux