RE: [PATCH net-next 1/5] dt-bindings: net: r8a779f0-ether-switch: Add ACLK

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello Conor,

> From: Conor Dooley, Sent: Tuesday, May 30, 2023 4:22 PM
> 
> Hey,
> 
> On Tue, May 30, 2023 at 12:19:46AM +0000, Yoshihiro Shimoda wrote:
> > > From: Conor Dooley, Sent: Tuesday, May 30, 2023 5:44 AM
> > > On Mon, May 29, 2023 at 10:11:12PM +0200, Andrew Lunn wrote:
> > > > On Mon, May 29, 2023 at 07:36:03PM +0100, Conor Dooley wrote:
> > > > > On Mon, May 29, 2023 at 05:08:36PM +0900, Yoshihiro Shimoda wrote:
> > > > > > Add ACLK of GWCA which needs to calculate registers' values for
> > > > > > rate limiter feature.
> > > > > >
> > > > > > Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@xxxxxxxxxxx>
> > > > > > ---
> > > > > >  .../bindings/net/renesas,r8a779f0-ether-switch.yaml    | 10 ++++++++--
> > > > > >  1 file changed, 8 insertions(+), 2 deletions(-)
> > > > > >
> > > > > > diff --git a/Documentation/devicetree/bindings/net/renesas,r8a779f0-ether-switch.yaml
> > > b/Documentation/devicetree/bindings/net/renesas,r8a779f0-ether-switch.yaml
> > > > > > index e933a1e48d67..cbe05fdcadaf 100644
> > > > > > --- a/Documentation/devicetree/bindings/net/renesas,r8a779f0-ether-switch.yaml
> > > > > > +++ b/Documentation/devicetree/bindings/net/renesas,r8a779f0-ether-switch.yaml
> > > > > > @@ -75,7 +75,12 @@ properties:
> > > > > >        - const: rmac2_phy
> > > > > >
> > > > > >    clocks:
> > > > > > -    maxItems: 1
> > > > > > +    maxItems: 2
> > > > > > +
> > > > > > +  clock-names:
> > > > > > +    items:
> > > > > > +      - const: fck
> > > > > > +      - const: aclk
> > > > >
> > > > > Since having both clocks is now required, please add some detail in the
> > > > > commit message about why that is the case. Reading it sounds like this
> > > > > is an optional new feature & not something that is required.
> > > >
> > > > This is something i wondered about, backwards compatibility with old
> > > > DT blobs. In the C code it is optional, and has a default clock rate
> > > > if the clock is not present.
> >
> > I'm sorry for lacking explanation. You're correct. this is backwards
> > compatibility with old DT blobs.
> >
> > > Yeah, I did the cursory check of the code to make sure that an old dtb
> > > would still function, which is part of why I am asking for the
> > > explanation of the enforcement here. I'm not clear on what the
> > > consequences of getting the default rate is. Perhaps if I read the whole
> > > series and understood the code I would be, but this commit should
> > > explain the why anyway & save me the trouble ;)
> >
> > The following clock rates are the same (400MHz):
> >  - default rate (RSWITCH_ACLK_DEFAULT) in the C code
> >  - R8A779F0_CLK_S0D2_HSC from dtb
> >
> > Only for backwards compatibility with old DT blobs, I added
> > the RSWITCH_ACLK_DEFAULT, and got the aclk as optional.
> >
> > By the way, R8A779F0_CLK_S0D2_HSC is fixed rate, and the r8a779f0-ether-switch
> > only uses the rswitch driver. Therefore, the clock rate is always 400MHz.
> > So, I'm thinking that the following implementation is enough.
> >  - no dt-bindings change. (In other words, don't add aclk in the dt-bindings.)
> >  - hardcoded the clock rate in the C code as 400MHz.
> >
> > > > So the yaml should not enforce an aclk member.
> > >
> > > This however I could go either way on. If the thing isn't going to
> > > function properly with the fallback rate, but would just limp on on
> > > in whatever broken way it has always done, I would agree with making
> > > the second clock required so that no new devicetrees are written in a
> > > way that would put the hardware into that broken state.
> > > On the other hand, if it works perfectly fine for some use cases without
> > > the second clock & just using the default rathe then I don't think the
> > > presence of the second clock should be enforced.
> >
> > Thank you very much for your comments! The it works perfectly fine for
> > all use cases without the second clock & just using the default rate.
> > That's why I'm now thinking that adding aclk into the dt-bindings is not
> > a good way...
> 
> I am biased, but I think the binding should describe the hardware &
> therefore the additional clock should be added.

I got it. I'll fix this patch on v2.

Best regards,
Yoshihiro Shimoda

> Cheers,
> Conor.




[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux