Two conversions to DT schema of GPIO watchdog binding happened and came through different trees. Merge them into one: 1. Combine maintainers, 2. Use more descriptive property descriptions and constraints from gpio-wdt.yaml, 3. Switch to unevaluatedProperties:false, to allow generic watchdog properties. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx> --- .../bindings/watchdog/gpio-wdt.yaml | 55 ------------------- .../bindings/watchdog/linux,wdt-gpio.yaml | 17 +++++- 2 files changed, 15 insertions(+), 57 deletions(-) delete mode 100644 Documentation/devicetree/bindings/watchdog/gpio-wdt.yaml diff --git a/Documentation/devicetree/bindings/watchdog/gpio-wdt.yaml b/Documentation/devicetree/bindings/watchdog/gpio-wdt.yaml deleted file mode 100644 index 155dc7965e9b..000000000000 --- a/Documentation/devicetree/bindings/watchdog/gpio-wdt.yaml +++ /dev/null @@ -1,55 +0,0 @@ -# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) -%YAML 1.2 ---- -$id: http://devicetree.org/schemas/watchdog/gpio-wdt.yaml# -$schema: http://devicetree.org/meta-schemas/core.yaml# - -title: GPIO controlled watchdog - -maintainers: - - Robert Marko <robert.marko@xxxxxxxxxx> - -properties: - compatible: - const: linux,wdt-gpio - - gpios: - maxItems: 1 - description: GPIO connected to the WDT reset pin - - hw_algo: - $ref: /schemas/types.yaml#/definitions/string - description: Algorithm used by the driver - oneOf: - - description: - Either a high-to-low or a low-to-high transition clears the WDT counter. - The watchdog timer is disabled when GPIO is left floating or connected - to a three-state buffer. - const: toggle - - description: - Low or high level starts counting WDT timeout, the opposite level - disables the WDT. - Active level is determined by the GPIO flags. - const: level - - hw_margin_ms: - $ref: /schemas/types.yaml#/definitions/uint32 - description: Maximum time to reset watchdog circuit (in milliseconds) - minimum: 2 - maximum: 65535 - - always-running: - type: boolean - description: - If the watchdog timer cannot be disabled, add this flag to have the driver - keep toggling the signal without a client. - It will only cease to toggle the signal when the device is open and the - timeout elapsed. - -required: - - compatible - - gpios - - hw_algo - - hw_margin_ms - -unevaluatedProperties: false diff --git a/Documentation/devicetree/bindings/watchdog/linux,wdt-gpio.yaml b/Documentation/devicetree/bindings/watchdog/linux,wdt-gpio.yaml index 50af79af6416..499f1b7e03f9 100644 --- a/Documentation/devicetree/bindings/watchdog/linux,wdt-gpio.yaml +++ b/Documentation/devicetree/bindings/watchdog/linux,wdt-gpio.yaml @@ -8,6 +8,7 @@ title: GPIO-controlled Watchdog maintainers: - Guenter Roeck <linux@xxxxxxxxxxxx> + - Robert Marko <robert.marko@xxxxxxxxxx> properties: compatible: @@ -19,11 +20,23 @@ properties: hw_algo: description: The algorithm used by the driver. - enum: [ level, toggle ] + oneOf: + - description: + Either a high-to-low or a low-to-high transition clears the WDT counter. + The watchdog timer is disabled when GPIO is left floating or connected + to a three-state buffer. + const: toggle + - description: + Low or high level starts counting WDT timeout, the opposite level + disables the WDT. + Active level is determined by the GPIO flags. + const: level hw_margin_ms: description: Maximum time to reset watchdog circuit (milliseconds). $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 2 + maximum: 65535 always-running: type: boolean @@ -42,7 +55,7 @@ required: allOf: - $ref: watchdog.yaml# -additionalProperties: false +unevaluatedProperties: false examples: - | -- 2.34.1
