Hi Tomi,
On Wed, Feb 15, 2023 at 08:29:47AM +0200, Tomi Valkeinen wrote:
> On 14/02/2023 02:37, Laurent Pinchart wrote:
> > On R-Car D3 and E3, the LVDS encoder provides the dot (pixel) clock to
> > the DU, regardless of whether the LVDS output is used or not. When using
> > the DPAD (RGB) output, the DU driver thus enables and disables the LVDS
> > PLL manually, while when using the LVDS output, it lets the LVDS bridge
> > driver handle the PLL configuration internally as part of the atomic
> > enable and disable operations.
> >
> > This causes an issue when using the LVDS output. As bridges are disabled
> > before CRTCs, the current implementation violates the enable/disable
> > sequences documented in the hardware datasheet, which requires the dot
> > clock to be enabled before the CRTC is started and disabled after it
> > gets stopped.
> >
> > Fix the problem by enabling/disabling the LVDS PLL manually from the DU
> > regardless of which output is used, and skipping the PLL handling in the
> > LVDS bridge atomic enable and disable operations.
> >
> > This is however not enough. Disabling the LVDS encoder while leaving the
> > PLL on still results in a vertical blanking wait timeout when disabling
> > the DU. Investigation showed that the culprit is the LVEN bit. For an
> > unclear reason, clearing the bit when disabling the LVDS encoder blocks
> > vertical blanking interrupts. We thus have to delay disabling the whole
> > LVDS encoder, not just disabling the PLL, until the DU is disabled.
> >
> > We could split the LVDS disable sequence by clearing the LVRES bit in
> > the LVDS bridge atomic disable handler, and delaying the rest of the
> > operations, in order to disable the LVDS output at bridge atomic disable
> > time, before stopping the CRTC. This would make the code more complex,
> > without a clear benefit, so keep the implementation simple(r).
>
> The asymmetry of all this makes me grit my teeth, but SW has to do what
> SW has to do...
I have the same feeling :-( It would be nice if the DU and LVDS were
better partitioned. And if we knew exactly what the hardware
requirements are regarding the start and stop sequences. Maybe we're
spoiled, we're not happy when we can get datasheets, and dream of
getting the RTL. Of course it may well turn into a nightmare if we
actually had access to that.
> Just a minor comment below, other than that:
>
> Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@xxxxxxxxxxxxxxxx>
>
> > Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@xxxxxxxxxxxxxxxx>
> > ---
> > drivers/gpu/drm/rcar-du/rcar_du_crtc.c | 18 ++--
> > drivers/gpu/drm/rcar-du/rcar_lvds.c | 114 +++++++++++++++----------
> > drivers/gpu/drm/rcar-du/rcar_lvds.h | 12 ++-
> > 3 files changed, 86 insertions(+), 58 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
> > index 008e172ed43b..71e7fbace38d 100644
> > --- a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
> > +++ b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
> > @@ -749,16 +749,17 @@ static void rcar_du_crtc_atomic_enable(struct drm_crtc *crtc,
> >
> > /*
> > * On D3/E3 the dot clock is provided by the LVDS encoder attached to
> > - * the DU channel. We need to enable its clock output explicitly if
> > - * the LVDS output is disabled.
> > + * the DU channel. We need to enable its clock output explicitly before
> > + * starting the CRTC, as the bridge hasn't been enabled by the atomic
> > + * helpers yet.
> > */
> > - if (rcdu->info->lvds_clk_mask & BIT(rcrtc->index) &&
> > - rstate->outputs == BIT(RCAR_DU_OUTPUT_DPAD0)) {
> > + if (rcdu->info->lvds_clk_mask & BIT(rcrtc->index)) {
> > + bool dot_clk_only = rstate->outputs == BIT(RCAR_DU_OUTPUT_DPAD0);
> > struct drm_bridge *bridge = rcdu->lvds[rcrtc->index];
> > const struct drm_display_mode *mode =
> > &crtc->state->adjusted_mode;
> >
> > - rcar_lvds_pclk_enable(bridge, mode->clock * 1000);
> > + rcar_lvds_pclk_enable(bridge, mode->clock * 1000, dot_clk_only);
> > }
> >
> > /*
> > @@ -795,15 +796,15 @@ static void rcar_du_crtc_atomic_disable(struct drm_crtc *crtc,
> > rcar_du_crtc_stop(rcrtc);
> > rcar_du_crtc_put(rcrtc);
> >
> > - if (rcdu->info->lvds_clk_mask & BIT(rcrtc->index) &&
> > - rstate->outputs == BIT(RCAR_DU_OUTPUT_DPAD0)) {
> > + if (rcdu->info->lvds_clk_mask & BIT(rcrtc->index)) {
> > + bool dot_clk_only = rstate->outputs == BIT(RCAR_DU_OUTPUT_DPAD0);
> > struct drm_bridge *bridge = rcdu->lvds[rcrtc->index];
> >
> > /*
> > * Disable the LVDS clock output, see
> > * rcar_du_crtc_atomic_enable().
> > */
>
> This could mention that when LVDS output is used, also the LVDS output
> is disabled here.
I'll write
/*
* Disable the LVDS clock output, see
* rcar_du_crtc_atomic_enable(). When the LVDS output is used,
* this also disables the LVDS encoder.
*/
> > - rcar_lvds_pclk_disable(bridge);
> > + rcar_lvds_pclk_disable(bridge, dot_clk_only);
> > }
> >
> > if ((rcdu->info->dsi_clk_mask & BIT(rcrtc->index)) &&
> > @@ -815,7 +816,6 @@ static void rcar_du_crtc_atomic_disable(struct drm_crtc *crtc,
> > * Disable the DSI clock output, see
> > * rcar_du_crtc_atomic_enable().
> > */
> > -
> > rcar_mipi_dsi_pclk_disable(bridge);
> > }
> >
> > diff --git a/drivers/gpu/drm/rcar-du/rcar_lvds.c b/drivers/gpu/drm/rcar-du/rcar_lvds.c
> > index 70cdd5ec64d5..ca215b588fd7 100644
> > --- a/drivers/gpu/drm/rcar-du/rcar_lvds.c
> > +++ b/drivers/gpu/drm/rcar-du/rcar_lvds.c
> > @@ -269,8 +269,8 @@ static void rcar_lvds_d3_e3_pll_calc(struct rcar_lvds *lvds, struct clk *clk,
> > pll->pll_m, pll->pll_n, pll->pll_e, pll->div);
> > }
> >
> > -static void __rcar_lvds_pll_setup_d3_e3(struct rcar_lvds *lvds,
> > - unsigned int freq, bool dot_clock_only)
> > +static void rcar_lvds_pll_setup_d3_e3(struct rcar_lvds *lvds,
> > + unsigned int freq, bool dot_clock_only)
> > {
> > struct pll_info pll = { .diff = (unsigned long)-1 };
> > u32 lvdpllcr;
> > @@ -305,11 +305,6 @@ static void __rcar_lvds_pll_setup_d3_e3(struct rcar_lvds *lvds,
> > rcar_lvds_write(lvds, LVDDIV, 0);
> > }
> >
> > -static void rcar_lvds_pll_setup_d3_e3(struct rcar_lvds *lvds, unsigned int freq)
> > -{
> > - __rcar_lvds_pll_setup_d3_e3(lvds, freq, false);
> > -}
> > -
> > /* -----------------------------------------------------------------------------
> > * Enable/disable
> > */
> > @@ -425,8 +420,12 @@ static void rcar_lvds_enable(struct drm_bridge *bridge,
> > /*
> > * PLL clock configuration on all instances but the companion in
> > * dual-link mode.
> > + *
> > + * The extended PLL has been turned on by an explicit call to
> > + * rcar_lvds_pclk_enable() from the DU driver.
> > */
> > - if (lvds->link_type == RCAR_LVDS_SINGLE_LINK || lvds->companion) {
> > + if ((lvds->link_type == RCAR_LVDS_SINGLE_LINK || lvds->companion) &&
> > + !(lvds->info->quirks & RCAR_LVDS_QUIRK_EXT_PLL)) {
> > const struct drm_crtc_state *crtc_state =
> > drm_atomic_get_new_crtc_state(state, crtc);
> > const struct drm_display_mode *mode =
> > @@ -491,11 +490,56 @@ static void rcar_lvds_enable(struct drm_bridge *bridge,
> > rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> > }
> >
> > +static void rcar_lvds_disable(struct drm_bridge *bridge)
> > +{
> > + struct rcar_lvds *lvds = bridge_to_rcar_lvds(bridge);
> > + u32 lvdcr0;
> > +
> > + /*
> > + * Clear the LVDCR0 bits in the order specified by the hardware
> > + * documentation, ending with a write of 0 to the full register to
> > + * clear all remaining bits.
> > + */
> > + lvdcr0 = rcar_lvds_read(lvds, LVDCR0);
> > +
> > + lvdcr0 &= ~LVDCR0_LVRES;
> > + rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> > +
> > + if (lvds->info->quirks & RCAR_LVDS_QUIRK_GEN3_LVEN) {
> > + lvdcr0 &= ~LVDCR0_LVEN;
> > + rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> > + }
> > +
> > + if (lvds->info->quirks & RCAR_LVDS_QUIRK_PWD) {
> > + lvdcr0 &= ~LVDCR0_PWD;
> > + rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> > + }
> > +
> > + if (!(lvds->info->quirks & RCAR_LVDS_QUIRK_EXT_PLL)) {
> > + lvdcr0 &= ~LVDCR0_PLLON;
> > + rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> > + }
> > +
> > + rcar_lvds_write(lvds, LVDCR0, 0);
> > + rcar_lvds_write(lvds, LVDCR1, 0);
> > +
> > + /* The extended PLL is turned off in rcar_lvds_pclk_disable(). */
> > + if (!(lvds->info->quirks & RCAR_LVDS_QUIRK_EXT_PLL))
> > + rcar_lvds_write(lvds, LVDPLLCR, 0);
> > +
> > + /* Disable the companion LVDS encoder in dual-link mode. */
> > + if (lvds->link_type != RCAR_LVDS_SINGLE_LINK && lvds->companion)
> > + rcar_lvds_disable(lvds->companion);
> > +
> > + pm_runtime_put_sync(lvds->dev);
> > +}
> > +
> > /* -----------------------------------------------------------------------------
> > * Clock - D3/E3 only
> > */
> >
> > -int rcar_lvds_pclk_enable(struct drm_bridge *bridge, unsigned long freq)
> > +int rcar_lvds_pclk_enable(struct drm_bridge *bridge, unsigned long freq,
> > + bool dot_clk_only)
> > {
> > struct rcar_lvds *lvds = bridge_to_rcar_lvds(bridge);
> > int ret;
> > @@ -509,13 +553,13 @@ int rcar_lvds_pclk_enable(struct drm_bridge *bridge, unsigned long freq)
> > if (ret)
> > return ret;
> >
> > - __rcar_lvds_pll_setup_d3_e3(lvds, freq, true);
> > + rcar_lvds_pll_setup_d3_e3(lvds, freq, dot_clk_only);
> >
> > return 0;
> > }
> > EXPORT_SYMBOL_GPL(rcar_lvds_pclk_enable);
> >
> > -void rcar_lvds_pclk_disable(struct drm_bridge *bridge)
> > +void rcar_lvds_pclk_disable(struct drm_bridge *bridge, bool dot_clk_only)
> > {
> > struct rcar_lvds *lvds = bridge_to_rcar_lvds(bridge);
> >
> > @@ -524,6 +568,9 @@ void rcar_lvds_pclk_disable(struct drm_bridge *bridge)
> >
> > dev_dbg(lvds->dev, "disabling LVDS PLL\n");
> >
> > + if (!dot_clk_only)
> > + rcar_lvds_disable(bridge);
> > +
> > rcar_lvds_write(lvds, LVDPLLCR, 0);
> >
> > pm_runtime_put_sync(lvds->dev);
> > @@ -552,42 +599,21 @@ static void rcar_lvds_atomic_disable(struct drm_bridge *bridge,
> > struct drm_bridge_state *old_bridge_state)
> > {
> > struct rcar_lvds *lvds = bridge_to_rcar_lvds(bridge);
> > - u32 lvdcr0;
> >
> > /*
> > - * Clear the LVDCR0 bits in the order specified by the hardware
> > - * documentation, ending with a write of 0 to the full register to
> > - * clear all remaining bits.
> > + * For D3 and E3, disabling the LVDS encoder before the DU would stall
> > + * the DU, causing a vblank wait timeout when stopping the DU. This has
> > + * been traced to clearing the LVEN bit, but the exact reason is
> > + * unknown. Keep the encoder enabled, it will be disabled by an explicit
> > + * call to rcar_lvds_pclk_disable() from the DU driver.
> > + *
> > + * We could clear the LVRES bit already to disable the LVDS output, but
> > + * that's likely pointless.
> > */
> > - lvdcr0 = rcar_lvds_read(lvds, LVDCR0);
> > + if (lvds->info->quirks & RCAR_LVDS_QUIRK_EXT_PLL)
> > + return;
> >
> > - lvdcr0 &= ~LVDCR0_LVRES;
> > - rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> > -
> > - if (lvds->info->quirks & RCAR_LVDS_QUIRK_GEN3_LVEN) {
> > - lvdcr0 &= ~LVDCR0_LVEN;
> > - rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> > - }
> > -
> > - if (lvds->info->quirks & RCAR_LVDS_QUIRK_PWD) {
> > - lvdcr0 &= ~LVDCR0_PWD;
> > - rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> > - }
> > -
> > - if (!(lvds->info->quirks & RCAR_LVDS_QUIRK_EXT_PLL)) {
> > - lvdcr0 &= ~LVDCR0_PLLON;
> > - rcar_lvds_write(lvds, LVDCR0, lvdcr0);
> > - }
> > -
> > - rcar_lvds_write(lvds, LVDCR0, 0);
> > - rcar_lvds_write(lvds, LVDCR1, 0);
> > - rcar_lvds_write(lvds, LVDPLLCR, 0);
> > -
> > - /* Disable the companion LVDS encoder in dual-link mode. */
> > - if (lvds->link_type != RCAR_LVDS_SINGLE_LINK && lvds->companion)
> > - rcar_lvds_atomic_disable(lvds->companion, old_bridge_state);
> > -
> > - pm_runtime_put_sync(lvds->dev);
> > + rcar_lvds_disable(bridge);
> > }
> >
> > static bool rcar_lvds_mode_fixup(struct drm_bridge *bridge,
> > @@ -924,14 +950,12 @@ static const struct rcar_lvds_device_info rcar_lvds_r8a77990_info = {
> > .gen = 3,
> > .quirks = RCAR_LVDS_QUIRK_GEN3_LVEN | RCAR_LVDS_QUIRK_EXT_PLL
> > | RCAR_LVDS_QUIRK_DUAL_LINK,
> > - .pll_setup = rcar_lvds_pll_setup_d3_e3,
> > };
> >
> > static const struct rcar_lvds_device_info rcar_lvds_r8a77995_info = {
> > .gen = 3,
> > .quirks = RCAR_LVDS_QUIRK_GEN3_LVEN | RCAR_LVDS_QUIRK_PWD
> > | RCAR_LVDS_QUIRK_EXT_PLL | RCAR_LVDS_QUIRK_DUAL_LINK,
> > - .pll_setup = rcar_lvds_pll_setup_d3_e3,
> > };
> >
> > static const struct of_device_id rcar_lvds_of_table[] = {
> > diff --git a/drivers/gpu/drm/rcar-du/rcar_lvds.h b/drivers/gpu/drm/rcar-du/rcar_lvds.h
> > index bee7033b60d6..887c63500000 100644
> > --- a/drivers/gpu/drm/rcar-du/rcar_lvds.h
> > +++ b/drivers/gpu/drm/rcar-du/rcar_lvds.h
> > @@ -13,17 +13,21 @@
> > struct drm_bridge;
> >
> > #if IS_ENABLED(CONFIG_DRM_RCAR_LVDS)
> > -int rcar_lvds_pclk_enable(struct drm_bridge *bridge, unsigned long freq);
> > -void rcar_lvds_pclk_disable(struct drm_bridge *bridge);
> > +int rcar_lvds_pclk_enable(struct drm_bridge *bridge, unsigned long freq,
> > + bool dot_clk_only);
> > +void rcar_lvds_pclk_disable(struct drm_bridge *bridge, bool dot_clk_only);
> > bool rcar_lvds_dual_link(struct drm_bridge *bridge);
> > bool rcar_lvds_is_connected(struct drm_bridge *bridge);
> > #else
> > static inline int rcar_lvds_pclk_enable(struct drm_bridge *bridge,
> > - unsigned long freq)
> > + unsigned long freq, bool dot_clk_only)
> > {
> > return -ENOSYS;
> > }
> > -static inline void rcar_lvds_pclk_disable(struct drm_bridge *bridge) { }
> > +static inline void rcar_lvds_pclk_disable(struct drm_bridge *bridge,
> > + bool dot_clock_only)
> > +{
> > +}
> > static inline bool rcar_lvds_dual_link(struct drm_bridge *bridge)
> > {
> > return false;
>
--
Regards,
Laurent Pinchart
