Hi Biju,
On Fri, Feb 10, 2023 at 5:01 PM Biju Das <biju.das.jz@xxxxxxxxxxxxxx> wrote:
> > On Fri, 10 Feb 2023, Biju Das wrote:
> > > As per HW manual section 40.6.1, we need to perform FIFO reset + SW
> > > reset before updating the below registers.
> > >
> > > FCR[7:5], FCR[3:0], LCR[7][5:0], MCR[6:4], DLL[7:0], DLM[7:0] and
> > > HCR0[6:5][3:2].
> > >
> > > This patch adds serial_out() to struct serial8250_em_hw_info to handle
> > > this difference between emma mobile and rz/v2m.
> > >
> > > DLL/DLM register can be updated only by setting LCR[7]. So the
> > > updation of LCR[7] will perform reset for DLL/DLM register changes.
> > >
> > > Signed-off-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
> > > --- a/drivers/tty/serial/8250/8250_em.c
> > > +++ b/drivers/tty/serial/8250/8250_em.c
> > > @@ -31,6 +35,40 @@ struct serial8250_em_priv {
> > > const struct serial8250_em_hw_info *info; };
> > >
> > > +static void serial8250_rzv2m_reg_update(struct uart_port *p, int off,
> > > +int value) {
> > > + unsigned int ier, fcr, lcr, mcr, hcr0;
> > > +
> > > + ier = readl(p->membase + (UART_IER << 2));
> > > + hcr0 = readl(p->membase + (UART_HCR0 << 2));
> > > + fcr = readl(p->membase + ((UART_FCR + 1) << 2));
> > > + lcr = readl(p->membase + ((UART_LCR + 1) << 2));
> > > + mcr = readl(p->membase + ((UART_MCR + 1) << 2));
> > > +
> > > + writel(fcr | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
> > > + p->membase + ((UART_FCR + 1) << 2));
> > > + writel(hcr0 | UART_HCR0_SW_RESET, p->membase + (UART_HCR0 << 2));
> > > + writel(hcr0 & ~UART_HCR0_SW_RESET, p->membase + (UART_HCR0 << 2));
> > > +
> > > + switch (off) {
> > > + case UART_FCR:
> > > + fcr = value;
> > > + break;
> > > + case UART_LCR:
> > > + lcr = value;
> > > + break;
> > > + case UART_MCR:
> > > + mcr = value;
> > > + break;
> > > + }
> > > +
> > > + writel(ier, p->membase + (UART_IER << 2));
> > > + writel(fcr, p->membase + ((UART_FCR + 1) << 2));
> > > + writel(mcr, p->membase + ((UART_MCR + 1) << 2));
> > > + writel(lcr, p->membase + ((UART_LCR + 1) << 2));
> > > + writel(hcr0, p->membase + (UART_HCR0 << 2));
> >
> > Perhaps it would make sense to instead of using readl/writel() directly to
> > call serial8250_em_serial_in/out() so all the offset trickery wouldn't need
> > to be duplicated inside this function?
>
> HCR0 register is not available for emma mobile. Is it ok if I just do readl/writel for
> that register and rest will use serial8250_em_serial_in/out()??
According to R19UH0040EJ0400 Rev.4.00 it is available on EMEV2,
and the layout looks identical to RZ/V2M.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
