[PATCH] memory: renesas-rpc-if: Remove redundant division of dummy

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Cong Dang <cong.dang.xn@xxxxxxxxxxx>

The dummy cycles value was wrongly calculated if dummy.buswidth > 1,
which affects QSPI, OSPI, HyperFlash on various SoCs. We're lucky in
Single SPI case since its dummy.buswidth equals to 1, so the result of
the division is unchanged

This issue can be reproduced using something like the following commands
A. QSPI mode: Mount device with jffs2 format
    jffs2: CLEANMARKER node found at 0x00000004, not first node in block (0x00000000)

B. QSPI mode: Write data to mtd10, where mtd10 is a parition on SPI Flash
storage, defined properly in a device tree

[Correct fragment, read from SPI Flash]

  root@v3x:~# echo "hello" > /dev/mtd10
  root@v3x:~# hexdump -C -n100 /dev/mtd10
  00000000  68 65 6c 6c 6f 0a ff ff  ff ff ff ff ff ff ff ff  |hello...........|
  00000010  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff  |................|

[Incorrect read of the same fragment: see the difference at offsets 0-3]

  root@v3x:~# echo "hello" > /dev/mtd10
  root@v3x:~# hexdump -C -n100 /dev/mtd10
  00000000  00 00 00 00 68 65 6c 6c  6f 0a ff ff ff ff ff ff  |....hello.......|
  00000010  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff  |................|

As seen from the result, 4 NULL bytes were inserted before the test data.
Wrong calculation in rpcif_prepare() led to miss of some dummy cycle. A
division by bus width is redundant because it had been performed already
in spi-rpc-if.c::rpcif_spi_mem_prepare()

Fix this by removing the redundant division.

Fixes: ca7d8b980b67 ("memory: add Renesas RPC-IF driver")
Signed-off-by: Cong Dang <cong.dang.xn@xxxxxxxxxxx>
Signed-off-by: Hai Pham <hai.pham.ud@xxxxxxxxxxx>
Signed-off-by: Wolfram Sang <wsa+renesas@xxxxxxxxxxxxxxxxxxxx>
---

Sadly, I cannot test this patch myself because I don't have access to
hardware which uses a buswidth > 1 for the dummy read. However, from
code review, this patch makes sense. The division by buswidth is done
twice, once in the SPI driver and once in the RPC core. It should stay
only in the SPI driver.

 drivers/memory/renesas-rpc-if.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/drivers/memory/renesas-rpc-if.c b/drivers/memory/renesas-rpc-if.c
index 09cd4318a83d..c36b407851ff 100644
--- a/drivers/memory/renesas-rpc-if.c
+++ b/drivers/memory/renesas-rpc-if.c
@@ -430,8 +430,7 @@ void rpcif_prepare(struct rpcif *rpc, const struct rpcif_op *op, u64 *offs,
 
 	if (op->dummy.buswidth) {
 		rpc->enable |= RPCIF_SMENR_DME;
-		rpc->dummy = RPCIF_SMDMCR_DMCYC(op->dummy.ncycles /
-						op->dummy.buswidth);
+		rpc->dummy = RPCIF_SMDMCR_DMCYC(op->dummy.ncycles);
 	}
 
 	if (op->option.buswidth) {
-- 
2.30.2




[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux