On 12/11/22 15:58, Prabhakar wrote:
> From: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
>
> Having a clocksource_arch_init() callback always sets vdso_clock_mode to
> VDSO_CLOCKMODE_ARCHTIMER if GENERIC_GETTIMEOFDAY is enabled, this is
> required for the riscv-timer.
>
> This works for platforms where just riscv-timer clocksource is present.
> On platforms where other clock sources are available we want them to
> register with vdso_clock_mode set to VDSO_CLOCKMODE_NONE.
>
> On the Renesas RZ/Five SoC OSTM block can be used as clocksource [0], to
> avoid multiple clock sources being registered as VDSO_CLOCKMODE_ARCHTIMER
> move setting of vdso_clock_mode in the riscv-timer driver instead of doing
> this in clocksource_arch_init() callback as done similarly for ARM/64
> architecture.
This is definitely a good change to make, but shouldn't we still prefer
the architectural CSR-based clocksource over an MMIO-based clocksource?
It has double the number of bits, and reading it should have less
overhead. So I think we also want to increase the rating of
riscv_clocksource.
D1 is in the same situation, as timer-sun4i.c registers a clocksource
with a higher rating than riscv_clocksource. Without this patch,
tools/testing/selftests/vDSO/vdso_test_correctness fails. With this
patch, it passes, so:
Tested-by: Samuel Holland <samuel@xxxxxxxxxxxx>
> [0] drivers/clocksource/renesas-ostm.c
>
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> ---
> arch/riscv/Kconfig | 1 -
> arch/riscv/kernel/time.c | 9 ---------
> drivers/clocksource/timer-riscv.c | 7 +++++++
> 3 files changed, 7 insertions(+), 10 deletions(-)
>
> diff --git a/arch/riscv/Kconfig b/arch/riscv/Kconfig
> index 7ea12de636bd..b269e062c1b1 100644
> --- a/arch/riscv/Kconfig
> +++ b/arch/riscv/Kconfig
> @@ -12,7 +12,6 @@ config 32BIT
>
> config RISCV
> def_bool y
> - select ARCH_CLOCKSOURCE_INIT
> select ARCH_ENABLE_HUGEPAGE_MIGRATION if HUGETLB_PAGE && MIGRATION
> select ARCH_ENABLE_SPLIT_PMD_PTLOCK if PGTABLE_LEVELS > 2
> select ARCH_HAS_BINFMT_FLAT
> diff --git a/arch/riscv/kernel/time.c b/arch/riscv/kernel/time.c
> index 8217b0f67c6c..42bee305e997 100644
> --- a/arch/riscv/kernel/time.c
> +++ b/arch/riscv/kernel/time.c
> @@ -30,12 +30,3 @@ void __init time_init(void)
> of_clk_init(NULL);
> timer_probe();
> }
> -
> -void clocksource_arch_init(struct clocksource *cs)
> -{
> -#ifdef CONFIG_GENERIC_GETTIMEOFDAY
> - cs->vdso_clock_mode = VDSO_CLOCKMODE_ARCHTIMER;
> -#else
> - cs->vdso_clock_mode = VDSO_CLOCKMODE_NONE;
> -#endif
> -}
> diff --git a/drivers/clocksource/timer-riscv.c b/drivers/clocksource/timer-riscv.c
> index 969a552da8d2..7ec9668cd36d 100644
> --- a/drivers/clocksource/timer-riscv.c
> +++ b/drivers/clocksource/timer-riscv.c
> @@ -29,6 +29,12 @@
>
> static DEFINE_STATIC_KEY_FALSE(riscv_sstc_available);
>
> +#ifdef CONFIG_GENERIC_GETTIMEOFDAY
> +static enum vdso_clock_mode vdso_default = VDSO_CLOCKMODE_ARCHTIMER;
> +#else
> +static enum vdso_clock_mode vdso_default = VDSO_CLOCKMODE_NONE;
> +#endif /* CONFIG_GENERIC_GETTIMEOFDAY */
We don't have any workarounds like arm_arch_timer, so we do not need
this indirection through vdso_default. You can set .vdso_clock_mode
directly in the declaration of riscv_clocksource.
Regards,
Samuel
> +
> static int riscv_clock_next_event(unsigned long delta,
> struct clock_event_device *ce)
> {
> @@ -158,6 +164,7 @@ static int __init riscv_timer_init_dt(struct device_node *n)
> return -ENODEV;
> }
>
> + riscv_clocksource.vdso_clock_mode = vdso_default;
> pr_info("%s: Registering clocksource cpuid [%d] hartid [%lu]\n",
> __func__, cpuid, hartid);
> error = clocksource_register_hz(&riscv_clocksource, riscv_timebase);
