Re: [PATCH v2 7/7] drm: rcar-du: dsi: Add r8a779g0 support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 29/11/2022 03:49, Laurent Pinchart wrote:

@@ -198,70 +436,53 @@ static void rcar_mipi_dsi_parameters_calc(struct rcar_mipi_dsi *dsi,
  	 */
  	fout_target = target * mipi_dsi_pixel_format_to_bpp(dsi->format)
  		    / (2 * dsi->lanes);
-	if (fout_target < 40000000 || fout_target > 1250000000)
+	if (fout_target < MHZ(40) || fout_target > MHZ(1250))
  		return;
/* Find vco_cntrl */
-	for (vco_cntrl = vco_cntrl_table; vco_cntrl->min_freq != 0; vco_cntrl++) {
-		if (fout_target > vco_cntrl->min_freq &&
-		    fout_target <= vco_cntrl->max_freq) {
-			setup_info->vco_cntrl = vco_cntrl->value;
-			if (fout_target >= 1150000000)
-				setup_info->prop_cntrl = 0x0c;
-			else
-				setup_info->prop_cntrl = 0x0b;
+	for (clkset = dsi->info->clk_cfg; clkset->min_freq != 0; clkset++) {
+		if (fout_target > clkset->min_freq &&
+		    fout_target <= clkset->max_freq) {
+			setup_info->clkset = clkset;
  			break;
  		}
  	}
- /* Add divider */
-	setup_info->div = (setup_info->vco_cntrl & 0x30) >> 4;
+	switch (dsi->info->model) {
+	case RCAR_DSI_R8A779A0:
+		setup_info->vclk_divider = 1 << ((clkset->vco_cntrl >> 4) & 0x3);

If you stored (clkset->vco_cntrl >> 4) & 0x3 in setup_info->vclk_divider
you wouldn't have to use __ffs() in rcar_mipi_dsi_startup(). You could
also drop the - 1 there, which would allow dropping one of the
switch(dsi->info->model). You can store the real divider value in
setup_info separately for rcar_mipi_dsi_pll_calc_r8a779a0(), or pass it
to the function.

That's true. The reason I chose this approach was to keep dsi_setup_info "neutral", containing only the logical values, and the register specific tinkering is done only where the register is written. Mixing the logical and the register values in the old dsi_setup_info was confusing, and implementing your suggestion would again go that direction. But as you noticed, this is uglified a bit by the need to get the divider from the vco_cntrl.

We could store the logical divider in the dsi_clk_config table, though, which would remove the need for the above code.

 Tomi




[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux