From: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx> Convert the simple OV5645 Device Tree binding to json-schema. The previous binding marked the below properties as required which was a driver requirement and not the device requirement so just drop them from the required list during the conversion. - clock-frequency - enable-gpios - reset-gpios Also drop the "clock-names" property as we have a single clock source for the sensor and the driver has been updated to drop the clk referencing by name. Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx> Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx> --- Resend v3: * No change v2 -> v3 * Dropped clock-names property * Marked power supplies as mandatory * Dropped the comment for voltage power supplies * Included RB tag from Laurent * Driver change to drop clock-names [0] [0] https://lore.kernel.org/linux-media/Yyh%2F3uzOJOu3drEB@xxxxxxxxxxxxxxxxxxxxxxxxxx/T/#t v1 -> v2 * Dropped ref to video-interface-devices.yaml# * Dropped driver specific required items from the list * Updated commit message * Dropped clock-lanes and bus-type from the port and example node * Marked data-lanes as required in port node --- .../devicetree/bindings/media/i2c/ov5645.txt | 54 --------- .../bindings/media/i2c/ovti,ov5645.yaml | 104 ++++++++++++++++++ 2 files changed, 104 insertions(+), 54 deletions(-) delete mode 100644 Documentation/devicetree/bindings/media/i2c/ov5645.txt create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov5645.yaml diff --git a/Documentation/devicetree/bindings/media/i2c/ov5645.txt b/Documentation/devicetree/bindings/media/i2c/ov5645.txt deleted file mode 100644 index 72ad992f77be..000000000000 --- a/Documentation/devicetree/bindings/media/i2c/ov5645.txt +++ /dev/null @@ -1,54 +0,0 @@ -* Omnivision 1/4-Inch 5Mp CMOS Digital Image Sensor - -The Omnivision OV5645 is a 1/4-Inch CMOS active pixel digital image sensor with -an active array size of 2592H x 1944V. It is programmable through a serial I2C -interface. - -Required Properties: -- compatible: Value should be "ovti,ov5645". -- clocks: Reference to the xclk clock. -- clock-names: Should be "xclk". -- clock-frequency: Frequency of the xclk clock. -- enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds - to the hardware pin PWDNB which is physically active low. -- reset-gpios: Chip reset GPIO. Polarity is GPIO_ACTIVE_LOW. This corresponds to - the hardware pin RESETB. -- vdddo-supply: Chip digital IO regulator. -- vdda-supply: Chip analog regulator. -- vddd-supply: Chip digital core regulator. - -The device node must contain one 'port' child node for its digital output -video port, in accordance with the video interface bindings defined in -Documentation/devicetree/bindings/media/video-interfaces.txt. - -Example: - - &i2c1 { - ... - - ov5645: ov5645@3c { - compatible = "ovti,ov5645"; - reg = <0x3c>; - - enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpio5 20 GPIO_ACTIVE_LOW>; - pinctrl-names = "default"; - pinctrl-0 = <&camera_rear_default>; - - clocks = <&clks 200>; - clock-names = "xclk"; - clock-frequency = <24000000>; - - vdddo-supply = <&camera_dovdd_1v8>; - vdda-supply = <&camera_avdd_2v8>; - vddd-supply = <&camera_dvdd_1v2>; - - port { - ov5645_ep: endpoint { - clock-lanes = <1>; - data-lanes = <0 2>; - remote-endpoint = <&csi0_ep>; - }; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5645.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5645.yaml new file mode 100644 index 000000000000..0b10483cd267 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5645.yaml @@ -0,0 +1,104 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5645.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OmniVision OV5645 Image Sensor Device Tree Bindings + +maintainers: + - Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx> + +properties: + compatible: + const: ovti,ov5645 + + reg: + maxItems: 1 + + clocks: + description: XCLK Input Clock + + clock-frequency: + description: Frequency of the xclk clock in Hz. + + vdda-supply: + description: Analog voltage supply, 2.8 volts + + vddd-supply: + description: Digital core voltage supply, 1.5 volts + + vdddo-supply: + description: Digital I/O voltage supply, 1.8 volts + + enable-gpios: + maxItems: 1 + description: + Reference to the GPIO connected to the PWDNB pin, if any. + + reset-gpios: + maxItems: 1 + description: + Reference to the GPIO connected to the RESETB pin, if any. + + port: + description: Digital Output Port + $ref: /schemas/graph.yaml#/$defs/port-base + additionalProperties: false + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + maxItems: 2 + items: + enum: [1, 2] + + required: + - data-lanes + +required: + - compatible + - reg + - clocks + - vdddo-supply + - vdda-supply + - vddd-supply + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + camera@3c { + compatible = "ovti,ov5645"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5645>; + reg = <0x3c>; + clocks = <&clks 1>; + clock-frequency = <24000000>; + vdddo-supply = <&ov5645_vdddo_1v8>; + vdda-supply = <&ov5645_vdda_2v8>; + vddd-supply = <&ov5645_vddd_1v5>; + enable-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; + + port { + ov5645_ep: endpoint { + remote-endpoint = <&csi0_ep>; + data-lanes = <1 2>; + }; + }; + }; + }; +... -- 2.25.1
