Hi Sergey,
> Subject: RE: [PATCH net-next v3] ravb: Add RZ/G2L MII interface support
>
> Hi Sergey,
>
> Thanks for the feedback.
>
> > Subject: Re: [PATCH net-next v3] ravb: Add RZ/G2L MII interface
> > support
> >
> > On 9/14/22 9:47 AM, Biju Das wrote:
> >
> > > EMAC IP found on RZ/G2L Gb ethernet supports MII interface.
> > > This patch adds support for selecting MII interface mode.
> > >
> > > Signed-off-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
> > > ---
> > > v2->v3:
> > > * Documented CXR35_HALFCYC_CLKSW1000 and CXR35_SEL_XMII_MII macros.
> >
> > I definitely didn't mean it done this way...
> >
> > [...]
> > > diff --git a/drivers/net/ethernet/renesas/ravb.h
> > > b/drivers/net/ethernet/renesas/ravb.h
> > > index b980bce763d3..058aceac8c92 100644
> > > --- a/drivers/net/ethernet/renesas/ravb.h
> > > +++ b/drivers/net/ethernet/renesas/ravb.h
> > [...]
> > > @@ -965,6 +966,11 @@ enum CXR31_BIT {
> > > CXR31_SEL_LINK1 = 0x00000008,
> > > };
> > >
> > > +enum CXR35_BIT {
> > > + CXR35_HALFCYC_CLKSW1000 = 0x03E80000, /* 1000 cycle of clk_chi
> > */
> >
> > No, please just declare:
>
>
> >
> > CXR35_HALFCYC_CLKSW = 0xffff0000,
>
> Q1) Why do you think we should use this value for setting MII?
>
> As per hardware manual the value you suggested is wrong for MII settings.
> See page 2157
>
> [A] The case which CXR35 SEL_XMII is used for the selection of RGMII/MII
> in APB Clock 100 MHz.
>
> (1) To use RGMII interface, Set ‘H’03E8 0000’ to this register.
> (2) To use MII interface, Set ‘H’03E8 0002’ to this register.
>
> >
> > > + CXR35_SEL_XMII_MII = 0x00000002, /* MII interface is used
> > */
> >
> > All the other register *enum*s are declared from LSB to MSB. The
> > comment is pretty self-obvious here, please remove it. And declare the
> > whole field too:
> >
> > CXR35_SEL_XMII = 0x00000003,
>
> Values 1 and 3 are reserved so we cannot use 3.
>
> I think the current patch holds good as per the hardware manual for
> selecting MII interface. Please recheck and correct me if it is wrong.
>
> Cheers,
> Biju
>
> > CXR35_SEL_XMII_RGMII = 0x00000000,
> > CXR35_SEL_XMII_MII = 0x00000002,
> >
> > [...]
> > > diff --git a/drivers/net/ethernet/renesas/ravb_main.c
> > > b/drivers/net/ethernet/renesas/ravb_main.c
> > > index b357ac4c56c5..9a0d06dd5eb6 100644
> > > --- a/drivers/net/ethernet/renesas/ravb_main.c
> > > +++ b/drivers/net/ethernet/renesas/ravb_main.c
> > > @@ -540,7 +540,14 @@ static void ravb_emac_init_gbeth(struct
> > > net_device
> > *ndev)
> > > /* E-MAC interrupt enable register */
> > > ravb_write(ndev, ECSIPR_ICDIP, ECSIPR);
> > >
> > > - ravb_modify(ndev, CXR31, CXR31_SEL_LINK0 | CXR31_SEL_LINK1,
> > CXR31_SEL_LINK0);
> > > + if (priv->phy_interface == PHY_INTERFACE_MODE_MII) {
> > > + ravb_modify(ndev, CXR31, CXR31_SEL_LINK0 | CXR31_SEL_LINK1,
> > 0);
> > > + ravb_write(ndev, CXR35_HALFCYC_CLKSW1000 | CXR35_SEL_XMII_MII,
> > > + CXR35);
> >
> > ravb_write(ndev, (1000 << 16) | CXR35_SEL_XMII_MII, CXR35);
Oops. Missed this magic number changes. Will send v4 with above suggestions.
Cheers,
Biju
