Convert the NXP SJA1000 CAN Controller Device Tree binding documentation to json-schema. Update the example to match reality. Signed-off-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx> --- .../bindings/net/can/nxp,sja1000.yaml | 106 ++++++++++++++++++ .../devicetree/bindings/net/can/sja1000.txt | 58 ---------- 2 files changed, 106 insertions(+), 58 deletions(-) create mode 100644 Documentation/devicetree/bindings/net/can/nxp,sja1000.yaml delete mode 100644 Documentation/devicetree/bindings/net/can/sja1000.txt diff --git a/Documentation/devicetree/bindings/net/can/nxp,sja1000.yaml b/Documentation/devicetree/bindings/net/can/nxp,sja1000.yaml new file mode 100644 index 000000000000..91d0f1b25d10 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/nxp,sja1000.yaml @@ -0,0 +1,106 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/can/nxp,sja1000.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Memory mapped SJA1000 CAN controller from NXP (formerly Philips) + +maintainers: + - Wolfgang Grandegger <wg@xxxxxxxxxxxxxx> + +properties: + compatible: + oneOf: + - description: NXP SJA1000 CAN Controller + const: nxp,sja1000 + - description: Technologic Systems SJA1000 CAN Controller + const: technologic,sja1000 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + reg-io-width: + $ref: /schemas/types.yaml#/definitions/uint32 + description: I/O register width (in bytes) implemented by this device + default: 1 + enum: [ 1, 2, 4 ] + + nxp,external-clock-frequency: + $ref: /schemas/types.yaml#/definitions/uint32 + default: 16000000 + description: | + Frequency of the external oscillator clock in Hz. + The internal clock frequency used by the SJA1000 is half of that value. + + nxp,tx-output-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1, 2, 3 ] + default: 1 + description: | + operation mode of the TX output control logic. Valid values are: + <0x0> : bi-phase output mode + <0x1> : normal output mode (default) + <0x2> : test output mode + <0x3> : clock output mode + + nxp,tx-output-config: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0x01, 0x02, 0x04, 0x06, 0x08, 0x10, 0x20, 0x30 ] + default: 0x02 + description: | + TX output pin configuration. Valid values are: + <0x01> : TX0 invert + <0x02> : TX0 pull-down (default) + <0x04> : TX0 pull-up + <0x06> : TX0 push-pull + <0x08> : TX1 invert + <0x10> : TX1 pull-down + <0x20> : TX1 pull-up + <0x30> : TX1 push-pull + + nxp,clock-out-frequency: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + clock frequency in Hz on the CLKOUT pin. + If not specified or if the specified value is 0, the CLKOUT pin + will be disabled. + + nxp,no-comparator-bypass: + type: boolean + description: Allows to disable the CAN input comparator. + +required: + - compatible + - reg + - interrupts + +allOf: + - $ref: can-controller.yaml# + + - if: + not: + properties: + compatible: + contains: + const: technologic,sja1000 + then: + required: + - reg-io-width + +unevaluatedProperties: false + +examples: + - | + can@1a000 { + #address-cells = <0x2>; + #size-cells = <0x1>; + + compatible = "technologic,sja1000"; + reg = <0x1a000 0x100>; + interrupts = <1>; + nxp,external-clock-frequency = <24000000>; + }; diff --git a/Documentation/devicetree/bindings/net/can/sja1000.txt b/Documentation/devicetree/bindings/net/can/sja1000.txt deleted file mode 100644 index ac3160eca96a..000000000000 --- a/Documentation/devicetree/bindings/net/can/sja1000.txt +++ /dev/null @@ -1,58 +0,0 @@ -Memory mapped SJA1000 CAN controller from NXP (formerly Philips) - -Required properties: - -- compatible : should be one of "nxp,sja1000", "technologic,sja1000". - -- reg : should specify the chip select, address offset and size required - to map the registers of the SJA1000. The size is usually 0x80. - -- interrupts: property with a value describing the interrupt source - (number and sensitivity) required for the SJA1000. - -Optional properties: - -- reg-io-width : Specify the size (in bytes) of the IO accesses that - should be performed on the device. Valid value is 1, 2 or 4. - This property is ignored for technologic version. - Default to 1 (8 bits). - -- nxp,external-clock-frequency : Frequency of the external oscillator - clock in Hz. Note that the internal clock frequency used by the - SJA1000 is half of that value. If not specified, a default value - of 16000000 (16 MHz) is used. - -- nxp,tx-output-mode : operation mode of the TX output control logic: - <0x0> : bi-phase output mode - <0x1> : normal output mode (default) - <0x2> : test output mode - <0x3> : clock output mode - -- nxp,tx-output-config : TX output pin configuration: - <0x01> : TX0 invert - <0x02> : TX0 pull-down (default) - <0x04> : TX0 pull-up - <0x06> : TX0 push-pull - <0x08> : TX1 invert - <0x10> : TX1 pull-down - <0x20> : TX1 pull-up - <0x30> : TX1 push-pull - -- nxp,clock-out-frequency : clock frequency in Hz on the CLKOUT pin. - If not specified or if the specified value is 0, the CLKOUT pin - will be disabled. - -- nxp,no-comparator-bypass : Allows to disable the CAN input comparator. - -For further information, please have a look to the SJA1000 data sheet. - -Examples: - -can@3,100 { - compatible = "nxp,sja1000"; - reg = <3 0x100 0x80>; - interrupts = <2 0>; - interrupt-parent = <&mpic>; - nxp,external-clock-frequency = <16000000>; -}; - -- 2.25.1
