Hi Jacopo,
Thank you for the patch.
On Sun, Oct 17, 2021 at 08:24:40PM +0200, Jacopo Mondi wrote:
> Use the routing table to configure the link output order and link
> masking.
>
> The link output order defines the CSI-2 virtual channel a GSML stream
s/GSML/GMSL/
> is output on. Configure ordering at stream start time and at chip
> setup time. This last step requires to move the chip initialization
> function after the V4L2 setup phase as it requires the subdev state from
> where the routing table is retrieved from to be initialized.
>
> Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
> ---
> drivers/media/i2c/max9286.c | 103 ++++++++++++++++++++++--------------
> 1 file changed, 64 insertions(+), 39 deletions(-)
>
> diff --git a/drivers/media/i2c/max9286.c b/drivers/media/i2c/max9286.c
> index 2e635179aec0..3485478f08a5 100644
> --- a/drivers/media/i2c/max9286.c
> +++ b/drivers/media/i2c/max9286.c
> @@ -500,6 +500,61 @@ static int max9286_check_config_link(struct max9286_priv *priv,
> return 0;
> }
>
> +/*
> + * Configure the links output order (which defines on which CSI-2 VC a
> + * link is output on) and configure link masking.
> + */
> +static void max9286_config_links(struct max9286_priv *priv)
> +{
> + const struct v4l2_subdev_krouting *routing;
> + struct v4l2_subdev_state *state;
> + u8 link_order = 0;
> + u8 vc_mask = 0xf;
> + unsigned int i;
> +
> + state = v4l2_subdev_lock_active_state(&priv->sd);
> + routing = &state->routing;
> +
> + for (i = 0; i < routing->num_routes; ++i) {
> + struct v4l2_subdev_route *route = &routing->routes[i];
> +
> + if (!(priv->route_mask & BIT(i)))
Shouldn't this be BIT(route->sink_pad), has route_mask stores a bitmask
of sink pads (see max9286_set_routing()) ?
> + continue;
> +
> + /* Assign the CSI-2 VC using the source stream number. */
> + link_order |= route->source_stream << (2 * route->sink_pad);
> + vc_mask &= ~BIT(route->source_stream);
> + }
> +
> + /*
> + * This might look rather silly, but now that we have assigned a
> + * VC to the enabled routes, we have to assign one to the disabled
> + * routes as well, as there cannot be two sources with the same VC.
> + */
> + for (i = 0; i < MAX9286_NUM_GMSL; ++i) {
> + unsigned int vc;
> +
> + if (priv->route_mask & BIT(i))
> + continue;
> +
> + /* ffs() counts from 1. */
> + vc = ffs(vc_mask) - 1;
> + link_order |= vc << (2 * i);
> + vc_mask &= ~BIT(vc);
> + }
> +
> + /*
> + * Use the enabled routes to enable GMSL links, configure the CSI-2
> + * output order, mask unused links and autodetect link used as CSI
> + * clock source.
> + */
> + max9286_write(priv, 0x00, MAX9286_MSTLINKSEL_AUTO | priv->route_mask);
> + max9286_write(priv, 0x0b, link_order);
> + max9286_write(priv, 0x69, 0xf & ~priv->route_mask);
> +
> + v4l2_subdev_unlock_state(state);
> +}
> +
> /* -----------------------------------------------------------------------------
> * V4L2 Subdev
> */
> @@ -701,6 +756,8 @@ static int max9286_s_stream(struct v4l2_subdev *sd, int enable)
> int ret;
>
> if (enable) {
> + max9286_config_links(priv);
> +
> /*
> * The frame sync between cameras is transmitted across the
> * reverse channel as GPIO. We must open all channels while
> @@ -1109,32 +1166,6 @@ static void max9286_v4l2_unregister(struct max9286_priv *priv)
>
> static int max9286_setup(struct max9286_priv *priv)
> {
> - /*
> - * Link ordering values for all enabled links combinations. Orders must
> - * be assigned sequentially from 0 to the number of enabled links
> - * without leaving any hole for disabled links. We thus assign orders to
> - * enabled links first, and use the remaining order values for disabled
> - * links are all links must have a different order value;
> - */
> - static const u8 link_order[] = {
> - (3 << 6) | (2 << 4) | (1 << 2) | (0 << 0), /* xxxx */
> - (3 << 6) | (2 << 4) | (1 << 2) | (0 << 0), /* xxx0 */
> - (3 << 6) | (2 << 4) | (0 << 2) | (1 << 0), /* xx0x */
> - (3 << 6) | (2 << 4) | (1 << 2) | (0 << 0), /* xx10 */
> - (3 << 6) | (0 << 4) | (2 << 2) | (1 << 0), /* x0xx */
> - (3 << 6) | (1 << 4) | (2 << 2) | (0 << 0), /* x1x0 */
> - (3 << 6) | (1 << 4) | (0 << 2) | (2 << 0), /* x10x */
> - (3 << 6) | (1 << 4) | (1 << 2) | (0 << 0), /* x210 */
> - (0 << 6) | (3 << 4) | (2 << 2) | (1 << 0), /* 0xxx */
> - (1 << 6) | (3 << 4) | (2 << 2) | (0 << 0), /* 1xx0 */
> - (1 << 6) | (3 << 4) | (0 << 2) | (2 << 0), /* 1x0x */
> - (2 << 6) | (3 << 4) | (1 << 2) | (0 << 0), /* 2x10 */
> - (1 << 6) | (0 << 4) | (3 << 2) | (2 << 0), /* 10xx */
> - (2 << 6) | (1 << 4) | (3 << 2) | (0 << 0), /* 21x0 */
> - (2 << 6) | (1 << 4) | (0 << 2) | (3 << 0), /* 210x */
> - (3 << 6) | (2 << 4) | (1 << 2) | (0 << 0), /* 3210 */
> - };
> -
> /*
> * Set the I2C bus speed.
> *
> @@ -1144,13 +1175,7 @@ static int max9286_setup(struct max9286_priv *priv)
> max9286_configure_i2c(priv, true);
> max9286_reverse_channel_setup(priv, priv->init_rev_chan_mv);
>
> - /*
> - * Enable GMSL links, mask unused ones and autodetect link
> - * used as CSI clock source.
> - */
> - max9286_write(priv, 0x00, MAX9286_MSTLINKSEL_AUTO | priv->route_mask);
> - max9286_write(priv, 0x0b, link_order[priv->route_mask]);
> - max9286_write(priv, 0x69, (0xf & ~priv->route_mask));
> + max9286_config_links(priv);
We could actually skip this, and only call
max9286_write(priv, 0x00, MAX9286_MSTLINKSEL_AUTO | priv->route_mask);
to enable the links. The link order and link masking is only needed when
starting the streams, which is done by calling max9286_config_links() in
max9286_s_stream().
>
> /*
> * Video format setup:
> @@ -1324,12 +1349,6 @@ static int max9286_init(struct device *dev)
> if (ret)
> return ret;
>
> - ret = max9286_setup(priv);
> - if (ret) {
> - dev_err(dev, "Unable to setup max9286\n");
> - goto err_poc_disable;
> - }
> -
> /*
> * Register all V4L2 interactions for the MAX9286 and notifiers for
> * any subdevices connected.
> @@ -1340,6 +1359,12 @@ static int max9286_init(struct device *dev)
> goto err_poc_disable;
> }
>
> + ret = max9286_setup(priv);
> + if (ret) {
> + dev_err(dev, "Unable to setup max9286\n");
> + goto err_poc_disable;
> + }
> +
And with the above change, I think you can keep the max9286_setup() call
where it was.
> ret = max9286_i2c_mux_init(priv);
> if (ret) {
> dev_err(dev, "Unable to initialize I2C multiplexer\n");
--
Regards,
Laurent Pinchart
