[PATCH 2/3] arm64: dts: renesas: rzg2l-smarc-som: Enable eMMC on SMARC platform

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



RZ/G2L SoM has both 64Gb eMMC and micro SD connected to SDHI0.

Both these interfaces are mutually exclusive and the SD0 device
selection is based on the XOR between GPIO_SD0_DEV_SEL and SW1[2]
switch position.

This patch sets GPIO_SD0_DEV_SEL to high in DT. Use the below switch
setting logic for device selection between eMMC and microSD slot
connected to SDHI0.

Set SW1[2] to position 2/OFF for selecting eMMC
Set SW1[2] to position 3/ON for selecting micro SD

This patch enables eMMC on RZ/G2L SMARC platform by default.

Signed-off-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
---
This patch has dependency upon [1]
[1] https://patchwork.kernel.org/project/linux-renesas-soc/list/?series=559045
---
 .../boot/dts/renesas/rzg2l-smarc-som.dtsi     | 145 ++++++++++++++++++
 1 file changed, 145 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi b/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi
index da1ee2206e1a..d83072009225 100644
--- a/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi
@@ -5,14 +5,55 @@
  * Copyright (C) 2021 Renesas Electronics Corp.
  */
 
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
 
+/* SW1[2] should be at position 2/OFF to enable 64Gb eMMC */
+#define EMMC	1
+
+/*
+ * To enable uSD card on CN3,
+ * SW1[2] should be at position 3/ON.
+ * Disable eMMC by setting "#define EMMC	0" above.
+ */
+#define SDHI	(!EMMC)
+
 / {
 	memory@48000000 {
 		device_type = "memory";
 		/* first 128MB is reserved for secure area. */
 		reg = <0x0 0x48000000 0x0 0x78000000>;
 	};
+
+	reg_1p8v: regulator0 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator1 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vccq_sdhi0: regulator-vccq-sdhi0 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI0 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		states = <3300000 1 1800000 0>;
+		regulator-boot-on;
+		gpios = <&pinctrl RZG2L_GPIO(39, 0) GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+	};
 };
 
 &adc {
@@ -32,4 +73,108 @@
 	adc_pins: adc {
 		pinmux = <RZG2L_PORT_PINMUX(9, 0, 2)>; /* ADC_TRG */
 	};
+
+	/*
+	 * SDO device selection is XOR between GPIO_SD0_DEV_SEL and SW1[2]
+	 * The below switch logic can be used to select the device between
+	 * eMMC and microSD, after setting GPIO_SD0_DEV_SEL to high in DT.
+	 * SW1[2] should be at position 2/OFF to enable 64Gb eMMC
+	 * SW1[2] should be at position 3/ON to enable uSD card CN3
+	 */
+	gpio_sd0_dev_sel {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(41, 1) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "gpio_sd0_dev_sel";
+	};
+
+	sd0_pwr_en {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(4, 1) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "sd0_pwr_en";
+	};
+
+	sdhi0_emmc_pins: sd0emmc {
+		sd0_emmc_data {
+			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3",
+			       "SD0_DATA4", "SD0_DATA5", "SD0_DATA6", "SD0_DATA7";
+			power-source  = <1800>;
+		};
+
+		sd0_emmc_ctrl {
+			pins = "SD0_CLK", "SD0_CMD";
+			power-source  = <1800>;
+		};
+
+		sd0_emmc_rst {
+			pins = "SD0_RST#";
+			power-source  = <1800>;
+		};
+	};
+
+	sdhi0_pins: sd0 {
+		sd0_data {
+			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
+			power-source  = <3300>;
+		};
+
+		sd0_ctrl {
+			pins = "SD0_CLK", "SD0_CMD";
+			power-source  = <3300>;
+		};
+
+		sd0_mux {
+			pinmux = <RZG2L_PORT_PINMUX(47, 0, 2)>; /* SD0_CD */
+		};
+	};
+
+	sdhi0_pins_uhs: sd0_uhs {
+		sd1_data_uhs {
+			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
+			power-source  = <1800>;
+		};
+
+		sd0_ctrl_uhs {
+			pins = "SD0_CLK", "SD0_CMD";
+			power-source  = <1800>;
+		};
+
+		sd0_mux_uhs {
+			pinmux = <RZG2L_PORT_PINMUX(47, 0, 2)>; /* SD0_CD */
+		};
+	};
+
 };
+
+#if SDHI
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_pins>;
+	pinctrl-1 = <&sdhi0_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&vccq_sdhi0>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+#endif
+
+#if EMMC
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_emmc_pins>;
+	pinctrl-1 = <&sdhi0_emmc_pins>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	fixed-emmc-driver-type = <1>;
+	status = "okay";
+};
+#endif
+
-- 
2.17.1




[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux