Re: [PATCH v3] serial: sh-sci: Stop dmaengine transfer in sci_stop_tx()

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Sergei,

On Wed, Jun 9, 2021 at 5:09 PM Sergei Shtylyov
<sergei.shtylyov@xxxxxxxxx> wrote:
> On 6/9/21 4:49 AM, Yoshihiro Shimoda wrote:
> > Stop dmaengine transfer in sci_stop_tx(). Otherwise, the following
> > message is possible output when system enters suspend and while
> > transferring data, because clearing TIE bit in SCSCR is not able to
> > stop any dmaengine transfer.
> >
> >     sh-sci e6550000.serial: ttySC1: Unable to drain transmitter
> >
> > Note that this patch uses dmaengine_terminate_async() so that
> > we can apply this patch into longterm kernel v4.9.x or later.
> >
> > Fixes: 73a19e4c0301 ("serial: sh-sci: Add DMA support.")
> > Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@xxxxxxxxxxx>
> > ---
> >  Changes from v2:
> >  - Don't use a macro.
> >  - Revise the commit descrption.
> >  https://lore.kernel.org/linux-renesas-soc/20210604095704.756190-1-yoshihiro.shimoda.uh@xxxxxxxxxxx/
> >
> >  Changes from v1:
> >  - Don't put #ifdef in the .c file.
> >  - Update the commit description.
> >  https://lore.kernel.org/linux-renesas-soc/20210602114108.510527-1-yoshihiro.shimoda.uh@xxxxxxxxxxx/
> >
> >  drivers/tty/serial/sh-sci.c | 8 ++++++++
> >  1 file changed, 8 insertions(+)
> >
> > diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c
> > index 4baf1316ea72..2d5487bf6855 100644
> > --- a/drivers/tty/serial/sh-sci.c
> > +++ b/drivers/tty/serial/sh-sci.c
> > @@ -610,6 +610,14 @@ static void sci_stop_tx(struct uart_port *port)
> >       ctrl &= ~SCSCR_TIE;
> >
> >       serial_port_out(port, SCSCR, ctrl);
> > +
> > +#ifdef CONFIG_SERIAL_SH_SCI_DMA
>
>    Why not use IS_ENABLED() instead? Gets rid of #ifdef. :-)
>
> > +     if (to_sci_port(port)->chan_tx &&
> > +         !dma_submit_error(to_sci_port(port)->cookie_tx)) {
> > +             dmaengine_terminate_async(to_sci_port(port)->chan_tx);
> > +             to_sci_port(port)->cookie_tx = -EINVAL;

Because chan_tx and cookie_tx do not exist if CONFIG_SERIAL_SH_SCI_DMA
is disabled.

Yes, that's why all the DMA code in this driver (.c file) is protected by
#ifdef CONFIG_SERIAL_SH_SCI_DMA.

> > +     }
> > +#endif
> >  }
> >
> >  static void sci_start_rx(struct uart_port *port)

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds



[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux