Re: [PATCH 09/16] media: i2c: rdacm21: Re-work OV10640 initialization

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Jacopo,

Thank you for the patch.

On Tue, Feb 16, 2021 at 06:41:39PM +0100, Jacopo Mondi wrote:
> The OV10640 image sensor reset and powerdown on signals are controlled

s/ on//

> by the embedded OV490 ISP. The current reset procedure does not respect
> the 1 millisecond power-up delay and releases the reset signal before
> the powerdown one.
> 
> Fix the OV10640 power up sequence by releasing the powerdown signal,
> waiting the mandatory 1 millisecond power up delay and then releasing
> the reset signal. The reset delay is not characterized in the chip
> manual if not as "255 XVCLK + initialization". Wait for at least 3
> milliseconds to guarantee the SCCB bus is available.
> 
> This commit fixes a sporadic start-up error triggered by a failure to
> read the OV10640 chip ID:
> rdacm21 8-0054: OV10640 ID mismatch: (0x01)
> 
> Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
> ---
>  drivers/media/i2c/rdacm21.c | 6 ++++--
>  1 file changed, 4 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/media/i2c/rdacm21.c b/drivers/media/i2c/rdacm21.c
> index b22a2ca5340b..c420a6b96879 100644
> --- a/drivers/media/i2c/rdacm21.c
> +++ b/drivers/media/i2c/rdacm21.c
> @@ -333,13 +333,15 @@ static int ov10640_initialize(struct rdacm21_device *dev)
>  {
>  	u8 val;
>  
> -	/* Power-up OV10640 by setting RESETB and PWDNB pins high. */
> +	/* Power-up OV10640 by setting PWDNB and RESETB pins high. */
>  	ov490_write_reg(dev, OV490_GPIO_SEL0, OV490_GPIO0);
>  	ov490_write_reg(dev, OV490_GPIO_SEL1, OV490_SPWDN0);
>  	ov490_write_reg(dev, OV490_GPIO_DIRECTION0, OV490_GPIO0);
>  	ov490_write_reg(dev, OV490_GPIO_DIRECTION1, OV490_SPWDN0);
> -	ov490_write_reg(dev, OV490_GPIO_OUTPUT_VALUE0, OV490_GPIO0);
> +
>  	ov490_write_reg(dev, OV490_GPIO_OUTPUT_VALUE0, OV490_SPWDN0);

Shouldn't this be OV490_GPIO_OUTPUT_VALUE1 ?

> +	usleep_range(1500, 3000);
> +	ov490_write_reg(dev, OV490_GPIO_OUTPUT_VALUE0, OV490_GPIO0);

I'm a bit puzzled by why this patch would improve the ID read issue,
given that it sets GPIO0 to 1, then sets GPIO0 to 1, compared to
previously setting GPIO0 to 1 following by setting GPIO0 to 1 :-) Maybe
it's the additional delay ? In any case, it would probably be a good
idea to perform additional tests after fixing this.

>  	usleep_range(3000, 5000);
>  
>  	/* Read OV10640 ID to test communications. */

-- 
Regards,

Laurent Pinchart



[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux