Hi Corentin,
On Tue, Jan 5, 2021 at 10:52 AM Corentin Labbe
<clabbe.montjoie@xxxxxxxxx> wrote:
> Due to DTB renaming, salvatorX was not booted since a long time in kernelCI.
> Now the rename is handled, the board fail to boot.
>
> I have bisected the problem:
> # first bad commit: [cfa7ede20f133cc81cef01dc3a516dda3a9721ee] arm64: set TEXT_OFFSET to 0x0 in preparation for removing it entirely
>
> This is the interesting part of uboot log:
> [ 0.000292] NOTI[ 0.000292] NOTICE: BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.16
> [ 0.005855] NOTICE: BL2: PRR is R-Car H3 Ver1.1
> [ 0.010437] NOTICE: BL2: Board is Salvator-X Rev1.0
> [ 0.015379] NOTICE: BL2: Boot device is HyperFlash(80MHz)
> [ 0.020804] NOTICE: BL2: LCM state is CM
> [ 0.024847] NOTICE: BL2: AVS setting succeeded. DVFS_SetVID=0x53
> [ 0.030891] NOTICE: BL2: DDR1600(rev.0.27)NOTICE: [COLD_BOOT]NOTICE: ..0
> [ 0.066311] NOTICE: BL2: DRAM Split is 4ch
> [ 0.070195] NOTICE: BL2: QoS is default setting(rev.0.37)
> [ 0.075697] NOTICE: BL2: Lossy Decomp areas
> [ 0.079872] NOTICE: Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
> [ 0.086957] NOTICE: Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
> [ 0.093869] NOTICE: Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
> [ 0.100785] NOTICE: BL2: v1.3(release):b330e0e
> [ 0.105274] NOTICE: BL2: Built : 15:26:51, Dec 6 2017
> [ 0.110462] NOTICE: BL2: Normal boot
> [ 0.114103] NOTICE: BL2: dst=0xe6320208 src=0x8180000 len=512(0x200)
> [ 0.120652] NOTICE: BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800)
> [ 0.127110] NOTICE: BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000)
> [ 0.134336] NOTICE: BL2: dst=0x44100000 src=0x8200000 len=524288(0x80000)
> [ 0.144816] NOTICE: BL2: dst=0x50000000 src=0x8640000 len=1048576(0x100000)
> U-Boot 2015.04 (Dec 06 2017 - 15:26:59)
> CPU: Renesas Electronics R8A7795 rev 1.1
> Board: Salvator-X
> I2C: ready
> DRAM: 3.9 GiB
> MMC: sh-sdhi: 0, sh-sdhi: 1, sh-sdhi: 2
> In: serial
> Out: serial
> Err: serial
> Net: ravb
>
> [...]
>
> booti 0x48080000 0x4a000000 0x48000000
^^^^^
I take it this is the problem?
For R-Car H3 ES1.0, I currently use the addresses below:
tftpboot 0x60000000 h3-salvator-x/Image
tftpboot 0x68000000 h3-salvator-x/r8a77950-salvator-x.dtb
booti 0x60000000 - 0x68000000
For R-Car H3 ES2.0 (and other R-Car Gen3 SoCs), I use other addresses:
tftpboot 0x50000000 h3-salvator-xs/Image
tftpboot 0x58000000 h3-salvator-xs/r8a77951-salvator-xs.dtb
booti 0x50000000 - 0x58000000
The firmware on your H3 ES1.1 board (Rev.1.0.16) is newer than on my
ES1.0 board (Rev.1.0.12), so it's possible the second version works on
your board, too.
If these work for you, I'll update https://elinux.org/R-Car/Boards/Salvator-X[S]
> ## Loading init Ramdisk from Legacy Image at 4a000000 ...
> Image Name:
> Image Type: AArch64 Linux RAMDisk Image (uncompressed)
> Data Size: 15809011 Bytes = 15.1 MiB
> Load Address: 00000000
> Entry Point: 00000000
> ERROR: Did not find a cmdline Flattened Device Tree
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
