[PATCH 1/4] i2c: rcar: faster irq code to minimize HW race condition

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



To avoid the HW race condition on R-Car Gen2 and earlier, we need to
write to ICMCR as soon as possible in the interrupt handler. We can
improve this by writing a static value instead of masking out bits.

Signed-off-by: Wolfram Sang <wsa+renesas@xxxxxxxxxxxxxxxxxxxx>
---
 drivers/i2c/busses/i2c-rcar.c | 11 ++++-------
 1 file changed, 4 insertions(+), 7 deletions(-)

diff --git a/drivers/i2c/busses/i2c-rcar.c b/drivers/i2c/busses/i2c-rcar.c
index 217def2d7cb4..824586d7ee56 100644
--- a/drivers/i2c/busses/i2c-rcar.c
+++ b/drivers/i2c/busses/i2c-rcar.c
@@ -91,7 +91,6 @@
 
 #define RCAR_BUS_PHASE_START	(MDBS | MIE | ESG)
 #define RCAR_BUS_PHASE_DATA	(MDBS | MIE)
-#define RCAR_BUS_MASK_DATA	(~(ESG | FSB) & 0xFF)
 #define RCAR_BUS_PHASE_STOP	(MDBS | MIE | FSB)
 
 #define RCAR_IRQ_SEND	(MNR | MAL | MST | MAT | MDE)
@@ -621,7 +620,7 @@ static bool rcar_i2c_slave_irq(struct rcar_i2c_priv *priv)
 /*
  * This driver has a lock-free design because there are IP cores (at least
  * R-Car Gen2) which have an inherent race condition in their hardware design.
- * There, we need to clear RCAR_BUS_MASK_DATA bits as soon as possible after
+ * There, we need to switch to RCAR_BUS_PHASE_DATA as soon as possible after
  * the interrupt was generated, otherwise an unwanted repeated message gets
  * generated. It turned out that taking a spinlock at the beginning of the ISR
  * was already causing repeated messages. Thus, this driver was converted to
@@ -630,13 +629,11 @@ static bool rcar_i2c_slave_irq(struct rcar_i2c_priv *priv)
 static irqreturn_t rcar_i2c_irq(int irq, void *ptr)
 {
 	struct rcar_i2c_priv *priv = ptr;
-	u32 msr, val;
+	u32 msr;
 
 	/* Clear START or STOP immediately, except for REPSTART after read */
-	if (likely(!(priv->flags & ID_P_REP_AFTER_RD))) {
-		val = rcar_i2c_read(priv, ICMCR);
-		rcar_i2c_write(priv, ICMCR, val & RCAR_BUS_MASK_DATA);
-	}
+	if (likely(!(priv->flags & ID_P_REP_AFTER_RD)))
+		rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_DATA);
 
 	msr = rcar_i2c_read(priv, ICMSR);
 
-- 
2.28.0




[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux