Re: [PATCH v3 2/7] dt-bindings: media: max9286: Document 'maxim,high-threshold'

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Jacopo,

On Fri, Oct 16, 2020 at 2:56 PM Jacopo Mondi <jacopo@xxxxxxxxxx> wrote:
> On Fri, Oct 16, 2020 at 01:50:34PM +0200, Geert Uytterhoeven wrote:
> > On Fri, Oct 16, 2020 at 12:09 PM Jacopo Mondi <jacopo+renesas@xxxxxxxxxx> wrote:
> > > Document the 'maxim,high-threshold' vendor property in the bindings
> > > document of the max9286 driver.
> > >
> > > The newly introduced boolean property allows controlling the initial
> > > configuration of the GMSL reverse control channel to accommodate
> > > remote serializers pre-programmed with the high threshold power
> > > supply noise immunity enabled.
> > >
> > > Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
> >
> > Thanks for your patch!
> >
> > > --- a/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml
> > > +++ b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml
> > > @@ -51,6 +51,19 @@ properties:
> > >    '#gpio-cells':
> > >      const: 2
> > >
> > > +  maxim,high-threshold:
> > > +    description: |
> > > +      A boolean property to increase the initial amplitude of the reverse
> > > +      control channel to compensate for remote serializers pre-programmed with
> > > +      high threshold noise-immunity.
> > > +
> > > +      Some camera modules (in example the RDACM20 one) include an on-board MCU
> > > +      that pre-programs the embedded serializer with reverse channel power
> > > +      supply noise immunity enabled. The deserializer shall increase its
> > > +      reverse channel amplitude to compensate that and be able to communicate
> > > +      with the remote end.
> > > +    type: boolean
> >
> > Does this "high" threshold correspond to some numerical value?
> > I.e. could we run into a future need to support more values than just
> > true/false?
> > If yes, we may want to use a numerical value from the start.
>
> So, this boolean property controls the initial setting of the reverse
> channel amplitude, which has to be opportunely adjusted to be able to
> probe the remote devices as i2c messages are bridged on the reverse
> channel from the deserializer to the remote serializers.
>
> It also implies that if the initial setting is not "high" it has to be
> increased after the remotes have probed, as it is assumed at the end
> the remotes' probe() routine they have enabled their high threshold
> noise immunity feature.
>
> The register that controls the de-serializer reverse channel amplitude
> is not fully documented in the chip manual version I have, but the
> application developer guide shows that it can range from 30mV to
> 200mV. The same developer guide shows 100mV and 170mV as "initial" and
> "high threshold" values to be used.
>
> On the serializer's side (MAX9271 at least) high threshold is a
> boolean control, it is either enabled or disabled.
>
> Hence I suspect that for the max9286-max9271 combo, using fixed 100mV
> and 170mV values is enough. Other serializers might allow a more fine
> grained control of the noise cancelling threshold, and might require a
> more precise adjustment of the deserializer side. I'm honestly not
> sure at this point not having seen any other one.
>
> So yes, this is a deserializer setting that depends on the serializer
> in use, and I'm not 100% comfortable expressing it as a deserializer
> property. That said, having an initial numerical value might serve the
> same purpose allowing more flexibility, if other serializers require a
> more precise control of the initial amplitude.
>
> After the remotes have probed, we could also re-explore the
> possibility of getting the bus configuration using get_mbus_config, as
> detailed in the v1 cover letter [1] as at that time their sub-devices
> have been registered and we can call operations on them. But again,
> this might be not required at all.

Sounds like "maxim,<foo>-threshold-mV" is the way to go?
If you don't know the exact register configuration, and need to
convert to a boolean in the driver, you can still use something like
"threshold < 150 ? ... : ...".

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds



[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux