Hi Lad, Thanks for your work. On 2020-08-03 17:02:53 +0100, Lad Prabhakar wrote: > Select the data pins for YCbCr422-8bit input format depending on > bus_width and data_shift passed as part of DT. > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx> > Reviewed-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx> > --- > Changes for v2: > * Dropped DT binding documentation patch > * Select the data pins depending on bus-width and data-shift I like this v2 much better then v1, nice work! > > v1 - > https://patchwork.kernel.org/project/linux-renesas-soc/list/?series=323799 > --- > drivers/media/platform/rcar-vin/rcar-core.c | 5 +++++ > drivers/media/platform/rcar-vin/rcar-dma.c | 7 +++++++ > drivers/media/platform/rcar-vin/rcar-vin.h | 5 +++++ > 3 files changed, 17 insertions(+) > > diff --git a/drivers/media/platform/rcar-vin/rcar-core.c b/drivers/media/platform/rcar-vin/rcar-core.c > index 7440c8965d27..55005d86928d 100644 > --- a/drivers/media/platform/rcar-vin/rcar-core.c > +++ b/drivers/media/platform/rcar-vin/rcar-core.c > @@ -624,6 +624,11 @@ static int rvin_parallel_parse_v4l2(struct device *dev, > vin->parallel = rvpe; > vin->parallel->mbus_type = vep->bus_type; > > + /* select VInDATA[15:8] pins for YCbCr422-8bit format */ > + if (vep->bus.parallel.bus_width == BUS_WIDTH_8 && > + vep->bus.parallel.data_shift == DATA_SHIFT_8) > + vin->parallel->ycbcr_8b_g = true; > + I would store the bus_width and bus_shift values in the struct rvin_parallel_entity and evaluate them in place rater then create a flag for this specific use-case.. Also according to the documentation is the check correct? Do we not wish to use the new mode when bus_width == 16 and bus_shift == 8. The check you have here seems to describe a 8 lane bus where 0 lanes are used. I think you should also verify that bus_shift is either 0 or 8 as that is all the driver supports. > switch (vin->parallel->mbus_type) { > case V4L2_MBUS_PARALLEL: > vin_dbg(vin, "Found PARALLEL media bus\n"); > diff --git a/drivers/media/platform/rcar-vin/rcar-dma.c b/drivers/media/platform/rcar-vin/rcar-dma.c > index 1a30cd036371..5db483877d65 100644 > --- a/drivers/media/platform/rcar-vin/rcar-dma.c > +++ b/drivers/media/platform/rcar-vin/rcar-dma.c > @@ -127,6 +127,8 @@ > #define VNDMR2_FTEV (1 << 17) > #define VNDMR2_VLV(n) ((n & 0xf) << 12) > > +#define VNDMR2_YDS BIT(22) This should be grouped with the other VNDMR2_* macros and not on its own. Also it should be sorted so it should be inserted between VNDMR2_CES and VNDMR2_FTEV. Also I know BIT() is a nice macro but the rest of the driver uses (1 << 22), please do the same for this one. > + > /* Video n CSI2 Interface Mode Register (Gen3) */ > #define VNCSI_IFMD_DES1 (1 << 26) > #define VNCSI_IFMD_DES0 (1 << 25) > @@ -698,6 +700,11 @@ static int rvin_setup(struct rvin_dev *vin) > /* Data Enable Polarity Select */ > if (vin->parallel->mbus_flags & V4L2_MBUS_DATA_ENABLE_LOW) > dmr2 |= VNDMR2_CES; > + > + if (vin->parallel->ycbcr_8b_g && vin->mbus_code == MEDIA_BUS_FMT_UYVY8_2X8) > + dmr2 |= VNDMR2_YDS; > + else > + dmr2 &= ~VNDMR2_YDS; dmr2 is already unitized and YDS is cleared, no need to clear it again if you don't wish to set it. Taking this and the comments above into account this would become something like (not tested), switch (vin->mbus_code) { case MEDIA_BUS_FMT_UYVY8_2X8: if (vin->parallel->bus_width == 16 && vin->parallel->bus_shift == 8) dmr2 |= VNDMR2_YDS; break; default: break; } > } > > /* > diff --git a/drivers/media/platform/rcar-vin/rcar-vin.h b/drivers/media/platform/rcar-vin/rcar-vin.h > index c19d077ce1cb..3126fee9a89b 100644 > --- a/drivers/media/platform/rcar-vin/rcar-vin.h > +++ b/drivers/media/platform/rcar-vin/rcar-vin.h > @@ -87,6 +87,9 @@ struct rvin_video_format { > u8 bpp; > }; > > +#define BUS_WIDTH_8 8 > +#define DATA_SHIFT_8 8 As pointed out by Geert, not so useful, use 8 in the code :-) > + > /** > * struct rvin_parallel_entity - Parallel video input endpoint descriptor > * @asd: sub-device descriptor for async framework > @@ -95,6 +98,7 @@ struct rvin_video_format { > * @mbus_flags: media bus configuration flags > * @source_pad: source pad of remote subdevice > * @sink_pad: sink pad of remote subdevice > + * @ycbcr_8b_g: select data pins for YCbCr422-8bit > * > */ > struct rvin_parallel_entity { > @@ -106,6 +110,7 @@ struct rvin_parallel_entity { > > unsigned int source_pad; > unsigned int sink_pad; > + bool ycbcr_8b_g; > }; > > /** > -- > 2.17.1 > -- Regards, Niklas Söderlund
