Convert the ov5640 bindings document to json-schema.
This commit ports the existing bindings, clean up patches
will follow.
Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
---
.../devicetree/bindings/media/i2c/ov5640.txt | 92 ---------
.../devicetree/bindings/media/i2c/ov5640.yaml | 181 ++++++++++++++++++
2 files changed, 181 insertions(+), 92 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/media/i2c/ov5640.txt
create mode 100644 Documentation/devicetree/bindings/media/i2c/ov5640.yaml
diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
deleted file mode 100644
index c97c2f2da12d..000000000000
--- a/Documentation/devicetree/bindings/media/i2c/ov5640.txt
+++ /dev/null
@@ -1,92 +0,0 @@
-* Omnivision OV5640 MIPI CSI-2 / parallel sensor
-
-Required Properties:
-- compatible: should be "ovti,ov5640"
-- clocks: reference to the xclk input clock.
-- clock-names: should be "xclk".
-- DOVDD-supply: Digital I/O voltage supply, 1.8 volts
-- AVDD-supply: Analog voltage supply, 2.8 volts
-- DVDD-supply: Digital core voltage supply, 1.5 volts
-
-Optional Properties:
-- reset-gpios: reference to the GPIO connected to the reset pin, if any.
- This is an active low signal to the OV5640.
-- powerdown-gpios: reference to the GPIO connected to the powerdown pin,
- if any. This is an active high signal to the OV5640.
-- rotation: as defined in
- Documentation/devicetree/bindings/media/video-interfaces.txt,
- valid values are 0 (sensor mounted upright) and 180 (sensor
- mounted upside down).
-
-The device node must contain one 'port' child node for its digital output
-video port, in accordance with the video interface bindings defined in
-Documentation/devicetree/bindings/media/video-interfaces.txt.
-
-OV5640 can be connected to a MIPI CSI-2 bus or a parallel bus endpoint.
-
-Endpoint node required properties for CSI-2 connection are:
-- remote-endpoint: a phandle to the bus receiver's endpoint node.
-- clock-lanes: should be set to <0> (clock lane on hardware lane 0)
-- data-lanes: should be set to <1> or <1 2> (one or two CSI-2 lanes supported)
-
-Endpoint node required properties for parallel connection are:
-- remote-endpoint: a phandle to the bus receiver's endpoint node.
-- bus-width: shall be set to <8> for 8 bits parallel bus
- or <10> for 10 bits parallel bus
-- data-shift: shall be set to <2> for 8 bits parallel bus
- (lines 9:2 are used) or <0> for 10 bits parallel bus
-- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
-- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
-- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock
- signal.
-
-Examples:
-
-&i2c1 {
- ov5640: camera@3c {
- compatible = "ovti,ov5640";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ov5640>;
- reg = <0x3c>;
- clocks = <&clks IMX6QDL_CLK_CKO>;
- clock-names = "xclk";
- DOVDD-supply = <&vgen4_reg>; /* 1.8v */
- AVDD-supply = <&vgen3_reg>; /* 2.8v */
- DVDD-supply = <&vgen2_reg>; /* 1.5v */
- powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
- reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
- rotation = <180>;
-
- port {
- /* MIPI CSI-2 bus endpoint */
- ov5640_to_mipi_csi2: endpoint {
- remote-endpoint = <&mipi_csi2_from_ov5640>;
- clock-lanes = <0>;
- data-lanes = <1 2>;
- };
- };
- };
-};
-
-&i2c1 {
- ov5640: camera@3c {
- compatible = "ovti,ov5640";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ov5640>;
- reg = <0x3c>;
- clocks = <&clk_ext_camera>;
- clock-names = "xclk";
-
- port {
- /* Parallel bus endpoint */
- ov5640_to_parallel: endpoint {
- remote-endpoint = <¶llel_from_ov5640>;
- bus-width = <8>;
- data-shift = <2>; /* lines 9:2 are used */
- hsync-active = <0>;
- vsync-active = <0>;
- pclk-sample = <1>;
- };
- };
- };
-};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.yaml b/Documentation/devicetree/bindings/media/i2c/ov5640.yaml
new file mode 100644
index 000000000000..ceeacc91c801
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov5640.yaml
@@ -0,0 +1,181 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ov5640.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Omnivision OV5640 MIPI CSI-2 / parallel sensor
+
+maintainers:
+ - Steve Longerbeam <slongerbeam@xxxxxxxxx>
+
+description: -|
+ The OV5640 is a 5 megapixels image sensor capable of producing images in RGB,
+ RAW, YUV and compressed formats. It features a MIPI CSI-2 and a parallel data
+ interface and an I2C-compatible (CCI) control interface.
+
+properties:
+ compatible:
+ const: ovti,ov5640
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ items:
+ - const: xclk
+
+ DOVDD-supply:
+ description: Digital I/O voltage supply, 1.8 volts.
+ maxItems: 1
+
+ AVDD-supply:
+ description: Analog voltage supply, 2.8 volts.
+ maxItems: 1
+
+ DVDD-supply:
+ description: Digital core voltage supply.
+ maxItems: 1
+
+ reset-gpios:
+ description: |
+ Reference to the GPIO connected to the reset pin, if any. This is an
+ active low signal to the OV5640.
+ maxItems: 1
+
+ powerdown-gpios:
+ description: |
+ Reference tot he GPIO connected to the powerdown pin, if any. This is an
+ active high signal to the OV5640.
+ maxItems: 1
+
+ rotation:
+ description: |
+ As defined in Documentation/devicetree/bindings/media/video-interfaces.txt
+ enum: [0, 180]
+
+ port:
+ type: object
+ description: |
+ The device node must contain one 'port' child node for its digital output
+ video port, in accordance with the video interface bindings defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+ OV5640 can be connected to a MIPI CSI-2 bus or a parallel bus endpoint.
+
+ properties:
+ endpoint:
+ type: object
+ properties:
+ remote-endpoint:
+ description: A phandle to the bus receiver's endpoint node.
+
+ clock-lanes:
+ const: 0
+
+ data-lanes:
+ description: |
+ Should be set to <1> or <1 2> (one or two CSI-2 lanes supported).
+ oneOf:
+ - items:
+ - const: 1
+ - items:
+ - const: 1
+ - const: 2
+
+ bus-width:
+ description: |
+ Shall be set to <8> for 8 bits parallel bus or <10> for 10 bits
+ parallel bus.
+ enum: [8, 10]
+
+ data-shift:
+ description: |
+ Shall be set to <2> for 8 bits parallel bus (lines 9:2 are used) or
+ <0> for 10 bits parallel bus.
+ enum: [0, 2]
+
+ hsync-active:
+ enum: [0, 1]
+
+ vsync-active:
+ enum: [0, 1]
+
+ pclk-sample:
+ enum: [0, 1]
+
+ required:
+ - remote-endpoint
+
+ additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - DOVDD-supply
+ - AVDD-supply
+ - DVDD-supply
+ - port
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/clock/imx6qdl-clock.h>
+
+ i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ camera@3c {
+ compatible = "ovti,ov5640";
+ reg = <0x3c>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ clock-names = "xclk";
+ DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+ AVDD-supply = <&vgen3_reg>; /* 2.8v */
+ DVDD-supply = <&vgen2_reg>; /* 1.5v */
+ powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+ rotation = <180>;
+
+ port {
+ ov5640_to_mipi_csi2: endpoint {
+ remote-endpoint = <&mipi_csi2_from_ov5640>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+ };
+
+ i2c1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ camera@3c {
+ compatible = "ovti,ov5640";
+ reg = <0x3c>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ clock-names = "xclk";
+ DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+ AVDD-supply = <&vgen3_reg>; /* 2.8v */
+ DVDD-supply = <&vgen2_reg>; /* 1.5v */
+ powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+ rotation = <180>;
+
+ port {
+ ov5640_to_parallel: endpoint {
+ remote-endpoint = <¶llel_from_ov5640>;
+ bus-width = <10>;
+ };
+ };
+ };
+ };
+
+...
--
2.27.0
