Hi Steve,
On Wed, Jul 15, 2020 at 10:04:04AM -0700, Steve Longerbeam wrote:
> Hi Jacopo,
>
> On 7/15/20 7:09 AM, Jacopo Mondi wrote:
> > Convert the ov5640 bindings document to json-schema and update
> > the MAINTAINERS file accordingly.
> >
> > Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
> > ---
> > Hi Steve,
> > I've added myself as maintainer in the bindings, with your ack
> > I would be happy to add myself as maintainer or reviewer for this driver
> > in MAINTAINERS, as I've recently been looking after this driver, mostly
> > for the MIPI CSI-2 interface part.
>
> Sure that's fine, I have not been involved in this driver at all, except for
> the initial commit. I don't think I should be listed as a MAINTAINER of this
> driver or its bindings either, so feel free to remove my name from both.
>
I was suggesting adding myself to the list of maintainers/reviewer,
not replacing you :) Hope that's not what you intended.
But in case you don't want to be bothered with this rather old driver
anymore, I could drop your name from there.
Thanks
j
> Steve
>
> >
> > Thanks
> > j
> >
> > ---
> > .../devicetree/bindings/media/i2c/ov5640.txt | 92 ---------
> > .../devicetree/bindings/media/i2c/ov5640.yaml | 181 ++++++++++++++++++
> > MAINTAINERS | 1 +
> > 3 files changed, 182 insertions(+), 92 deletions(-)
> > delete mode 100644 Documentation/devicetree/bindings/media/i2c/ov5640.txt
> > create mode 100644 Documentation/devicetree/bindings/media/i2c/ov5640.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
> > deleted file mode 100644
> > index c97c2f2da12d..000000000000
> > --- a/Documentation/devicetree/bindings/media/i2c/ov5640.txt
> > +++ /dev/null
> > @@ -1,92 +0,0 @@
> > -* Omnivision OV5640 MIPI CSI-2 / parallel sensor
> > -
> > -Required Properties:
> > -- compatible: should be "ovti,ov5640"
> > -- clocks: reference to the xclk input clock.
> > -- clock-names: should be "xclk".
> > -- DOVDD-supply: Digital I/O voltage supply, 1.8 volts
> > -- AVDD-supply: Analog voltage supply, 2.8 volts
> > -- DVDD-supply: Digital core voltage supply, 1.5 volts
> > -
> > -Optional Properties:
> > -- reset-gpios: reference to the GPIO connected to the reset pin, if any.
> > - This is an active low signal to the OV5640.
> > -- powerdown-gpios: reference to the GPIO connected to the powerdown pin,
> > - if any. This is an active high signal to the OV5640.
> > -- rotation: as defined in
> > - Documentation/devicetree/bindings/media/video-interfaces.txt,
> > - valid values are 0 (sensor mounted upright) and 180 (sensor
> > - mounted upside down).
> > -
> > -The device node must contain one 'port' child node for its digital output
> > -video port, in accordance with the video interface bindings defined in
> > -Documentation/devicetree/bindings/media/video-interfaces.txt.
> > -
> > -OV5640 can be connected to a MIPI CSI-2 bus or a parallel bus endpoint.
> > -
> > -Endpoint node required properties for CSI-2 connection are:
> > -- remote-endpoint: a phandle to the bus receiver's endpoint node.
> > -- clock-lanes: should be set to <0> (clock lane on hardware lane 0)
> > -- data-lanes: should be set to <1> or <1 2> (one or two CSI-2 lanes supported)
> > -
> > -Endpoint node required properties for parallel connection are:
> > -- remote-endpoint: a phandle to the bus receiver's endpoint node.
> > -- bus-width: shall be set to <8> for 8 bits parallel bus
> > - or <10> for 10 bits parallel bus
> > -- data-shift: shall be set to <2> for 8 bits parallel bus
> > - (lines 9:2 are used) or <0> for 10 bits parallel bus
> > -- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
> > -- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
> > -- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock
> > - signal.
> > -
> > -Examples:
> > -
> > -&i2c1 {
> > - ov5640: camera@3c {
> > - compatible = "ovti,ov5640";
> > - pinctrl-names = "default";
> > - pinctrl-0 = <&pinctrl_ov5640>;
> > - reg = <0x3c>;
> > - clocks = <&clks IMX6QDL_CLK_CKO>;
> > - clock-names = "xclk";
> > - DOVDD-supply = <&vgen4_reg>; /* 1.8v */
> > - AVDD-supply = <&vgen3_reg>; /* 2.8v */
> > - DVDD-supply = <&vgen2_reg>; /* 1.5v */
> > - powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
> > - reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
> > - rotation = <180>;
> > -
> > - port {
> > - /* MIPI CSI-2 bus endpoint */
> > - ov5640_to_mipi_csi2: endpoint {
> > - remote-endpoint = <&mipi_csi2_from_ov5640>;
> > - clock-lanes = <0>;
> > - data-lanes = <1 2>;
> > - };
> > - };
> > - };
> > -};
> > -
> > -&i2c1 {
> > - ov5640: camera@3c {
> > - compatible = "ovti,ov5640";
> > - pinctrl-names = "default";
> > - pinctrl-0 = <&pinctrl_ov5640>;
> > - reg = <0x3c>;
> > - clocks = <&clk_ext_camera>;
> > - clock-names = "xclk";
> > -
> > - port {
> > - /* Parallel bus endpoint */
> > - ov5640_to_parallel: endpoint {
> > - remote-endpoint = <¶llel_from_ov5640>;
> > - bus-width = <8>;
> > - data-shift = <2>; /* lines 9:2 are used */
> > - hsync-active = <0>;
> > - vsync-active = <0>;
> > - pclk-sample = <1>;
> > - };
> > - };
> > - };
> > -};
> > diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.yaml b/Documentation/devicetree/bindings/media/i2c/ov5640.yaml
> > new file mode 100644
> > index 000000000000..9c32262a3621
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/i2c/ov5640.yaml
> > @@ -0,0 +1,181 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/media/i2c/ov5640.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Omnivision OV5640 MIPI CSI-2 / parallel sensor
> > +
> > +maintainers:
> > + - Steve Longerbeam <slongerbeam@xxxxxxxxx>
> > + - Jacopo Mondi <jacopo@xxxxxxxxxx>
> > +
> > +description: -|
> > + OV5640 is a 5 megapixels image sensor capable of producing images in RBG, RAW,
> > + YUV and compressed formats. It features a MIPI CSI-2 and a parallel data
> > + interface and an I2C-compatible (CCI) control interface.
> > +
> > +properties:
> > + compatible:
> > + const: ovti,ov5640
> > +
> > + reg:
> > + description: I2C device address
> > + maxItems: 1
> > +
> > + clocks:
> > + description: Reference to the xclk input clock.
> > + maxItems: 1
> > +
> > + clock-names:
> > + description: Should be "xclk".
> > + maxItems: 1
> > +
> > + DOVDD-supply:
> > + description: Digital I/O voltage supply, 1.8 volts.
> > + maxItems: 1
> > +
> > + AVDD-supply:
> > + description: Analog voltage supply, 2.8 volts.
> > + maxItems: 1
> > +
> > + DVDD-supply:
> > + description: Digital core voltage supply.
> > + maxItems: 1
> > +
> > + reset-gpios:
> > + description: |
> > + Reference to the GPIO connected to the reset pin, if any. This is an
> > + active low signal to the OV5640.
> > + maxItems: 1
> > +
> > + powerdown-gpios:
> > + description: |
> > + Reference tot he GPIO connected to the powerdown pin, if any. This is an
> > + active high signal to the OV5640.
> > + maxItems: 1
> > +
> > + rotation:
> > + description: |
> > + As defined in Documentation/devicetree/bindings/media/video-interfaces.txt,
> > + valid values are 0 (sensor mounted upright) and 180 (sensor mounted upside
> > + down).
> > +
> > + port:
> > + type: object
> > + description: |
> > + The device node must contain one 'port' child node for its digital output
> > + video port, in accordance with the video interface bindings defined in
> > + Documentation/devicetree/bindings/media/video-interfaces.txt.
> > +
> > + OV5640 can be connected to a MIPI CSI-2 bus or a parallel bus endpoint.
> > +
> > + properties:
> > + endpoint:
> > + type: object
> > + properties:
> > + remote-endpoint:
> > + description: A phandle to the bus receiver's endpoint node.
> > +
> > + clock-lanes:
> > + description: Should be set to 0 (clock lane on hardware lane 0).
> > +
> > + data-lanes:
> > + description: |
> > + Should be set to <1> or <1 2> (one or two CSI-2 lanes supported).
> > +
> > + bus-width:
> > + description: |
> > + Shall be set to <8> for 8 bits parallel bus or <10> for 10 bits
> > + parallel bus.
> > +
> > + data-shift:
> > + description: |
> > + Shall be set to <2> for 8 bits parallel bus (lines 9:2 are used) or
> > + <0> for 10 bits parallel bus.
> > +
> > + hsync-active:
> > + description: |
> > + Active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
> > +
> > + vsync-active:
> > + description: |
> > + Active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
> > +
> > + pclk-sample:
> > + description: |
> > + Sample data on rising (1) or falling (0) edge of the pixel clock
> > + signal.
> > +
> > + required:
> > + - remote-endpoint
> > +
> > + additionalProperties: false
> > +
> > +required:
> > + - compatible
> > + - reg
> > + - clocks
> > + - clock-names
> > + - DOVDD-supply
> > + - AVDD-supply
> > + - DVDD-supply
> > + - port
> > +
> > +examples:
> > + - |
> > + #include <dt-bindings/gpio/gpio.h>
> > + #include <dt-bindings/clock/imx6qdl-clock.h>
> > +
> > + i2c0 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + camera@3c {
> > + compatible = "ovti,ov5640";
> > + reg = <0x3c>;
> > + clocks = <&clks IMX6QDL_CLK_CKO>;
> > + clock-names = "xclk";
> > + DOVDD-supply = <&vgen4_reg>; /* 1.8v */
> > + AVDD-supply = <&vgen3_reg>; /* 2.8v */
> > + DVDD-supply = <&vgen2_reg>; /* 1.5v */
> > + powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
> > + reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
> > + rotation = <180>;
> > +
> > + port {
> > + ov5640_to_mipi_csi2: endpoint {
> > + remote-endpoint = <&mipi_csi2_from_ov5640>;
> > + clock-lanes = <0>;
> > + data-lanes = <1 2>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + i2c1 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + camera@3c {
> > + compatible = "ovti,ov5640";
> > + reg = <0x3c>;
> > + clocks = <&clks IMX6QDL_CLK_CKO>;
> > + clock-names = "xclk";
> > + DOVDD-supply = <&vgen4_reg>; /* 1.8v */
> > + AVDD-supply = <&vgen3_reg>; /* 2.8v */
> > + DVDD-supply = <&vgen2_reg>; /* 1.5v */
> > + powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
> > + reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
> > + rotation = <180>;
> > +
> > + port {
> > + ov5640_to_parallel: endpoint {
> > + remote-endpoint = <¶llel_from_ov5640>;
> > + bus-width = <8>;
> > + };
> > + };
> > + };
> > + };
> > +
> > +...
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index c74d25c58e1a..0160d7567ed3 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -12605,6 +12605,7 @@ L: linux-media@xxxxxxxxxxxxxxx
> > S: Maintained
> > T: git git://linuxtv.org/media_tree.git
> > F: drivers/media/i2c/ov5640.c
> > +F: Documentation/devicetree/bindings/media/i2c/ov5640.yaml
> >
> > OMNIVISION OV5647 SENSOR DRIVER
> > M: Jacopo Mondi <jacopo@xxxxxxxxxx>
> > --
> > 2.27.0
> >
>
