[PATCH 2/3] dt-bindings: adv7604: Convert bindings to json-schema

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Convert ADV7604 video decoder documentation to json-schema.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@xxxxxxxxxxxx>
---
 .../devicetree/bindings/media/i2c/adv7604.txt |  87 ---------
 .../bindings/media/i2c/adv7604.yaml           | 171 ++++++++++++++++++
 2 files changed, 171 insertions(+), 87 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/media/i2c/adv7604.txt
 create mode 100644 Documentation/devicetree/bindings/media/i2c/adv7604.yaml

diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt
deleted file mode 100644
index 8c7cdc7cd7aaebc8..0000000000000000
--- a/Documentation/devicetree/bindings/media/i2c/adv7604.txt
+++ /dev/null
@@ -1,87 +0,0 @@
-* Analog Devices ADV7604/11/12 video decoder with HDMI receiver
-
-The ADV7604 and ADV7611/12 are multiformat video decoders with an integrated
-HDMI receiver. The ADV7604 has four multiplexed HDMI inputs and one analog
-input, and the ADV7611 has one HDMI input and no analog input. The 7612 is
-similar to the 7611 but has 2 HDMI inputs.
-
-These device tree bindings support the ADV7611/12 only at the moment.
-
-Required Properties:
-
-  - compatible: Must contain one of the following
-    - "adi,adv7611" for the ADV7611
-    - "adi,adv7612" for the ADV7612
-
-  - reg: I2C slave addresses
-    The ADV76xx has up to thirteen 256-byte maps that can be accessed via the
-    main I2C ports. Each map has it own I2C address and acts as a standard
-    slave device on the I2C bus. The main address is mandatory, others are
-    optional and revert to defaults if not specified.
-
-The device node must contain one 'port' child node per device input and output
-port, in accordance with the video interface bindings defined in
-Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
-are numbered as follows.
-
-  Port			ADV7611    ADV7612
-------------------------------------------------------------
-  HDMI			0             0, 1
-  Digital output	1                2
-
-The digital output port node must contain at least one endpoint.
-
-Optional Properties:
-
-  - hpd-gpios: References to the GPIOs that control the HDMI hot-plug
-    detection pins, one per HDMI input. The active flag indicates the GPIO
-    level that enables hot-plug detection.
-  - reset-gpios: Reference to the GPIO connected to the device's reset pin.
-  - default-input: Select which input is selected after reset.
-  - reg-names : Names of maps with programmable addresses.
-		It can contain any map needing a non-default address.
-		Possible maps names are :
-		  "main", "avlink", "cec", "infoframe", "esdp", "dpp", "afe",
-		  "rep", "edid", "hdmi", "test", "cp", "vdp"
-
-Optional Endpoint Properties:
-
-  The following three properties are defined in video-interfaces.txt and are
-  valid for source endpoints only.
-
-  - hsync-active: Horizontal synchronization polarity. Defaults to active low.
-  - vsync-active: Vertical synchronization polarity. Defaults to active low.
-  - pclk-sample: Pixel clock polarity. Defaults to output on the falling edge.
-
-  If none of hsync-active, vsync-active and pclk-sample is specified the
-  endpoint will use embedded BT.656 synchronization.
-
-Example:
-
-	hdmi_receiver@4c {
-		compatible = "adi,adv7611";
-		/*
-		 * The edid page will be accessible @ 0x66 on the I2C bus. All
-		 * other maps will retain their default addresses.
-		 */
-		reg = <0x4c>, <0x66>;
-		reg-names = "main", "edid";
-
-		reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>;
-		hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>;
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		default-input = <0>;
-
-		port@0 {
-			reg = <0>;
-		};
-		port@1 {
-			reg = <1>;
-			hdmi_in: endpoint {
-				remote-endpoint = <&ccdc_in>;
-			};
-		};
-	};
diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.yaml b/Documentation/devicetree/bindings/media/i2c/adv7604.yaml
new file mode 100644
index 0000000000000000..d354fd8e0cc88d93
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adv7604.yaml
@@ -0,0 +1,171 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/adv7604.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices ADV7604/11/12 video decoder with HDMI receiver
+
+maintainers:
+  - Hans Verkuil <hverkuil-cisco@xxxxxxxxx>
+
+description:
+  The ADV7604 and ADV7611/12 are multiformat video decoders with an integrated
+  HDMI receiver. The ADV7604 has four multiplexed HDMI inputs and one analog
+  input, and the ADV7611 has one HDMI input and no analog input. The 7612 is
+  similar to the 7611 but has 2 HDMI inputs.
+
+  These device tree bindings support the ADV7611/12 only at the moment.
+
+properties:
+  compatible:
+    items:
+      - enum:
+        - adi,adv7611
+        - adi,adv7612
+
+  reg:
+    minItems: 1
+    maxItems: 13
+
+  reg-names:
+    items:
+      - enum: [ main, avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ main, avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ main, avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ main, avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ main, avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ main, avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ main, avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ main, avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ main, avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ main, avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ main, avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ main, avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+      - enum: [ main, avlink, cec, infoframe, esdp, dpp, afe, rep, edid, hdmi, test, cp, vdp ]
+
+  reset-gpios:
+    maxItems: 1
+
+  hpd-gpios:
+    minItems: 1
+    description:
+      References to the GPIOs that control the HDMI hot-plug detection pins,
+      one per HDMI input. The active flag indicates the GPIO level that
+      enables hot-plug detection.
+
+  default-input:
+    maxItems: 1
+    description:
+      Select which input is selected after reset.
+
+  ports:
+    type: object
+    description:
+      A node containing input and output port nodes with endpoint definitions
+      as documented in
+      Documentation/devicetree/bindings/media/video-interfaces.txt
+
+required:
+  - compatible
+  - reg
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: adi,adv7611
+    then:
+      properties:
+        ports:
+          properties:
+            '#address-cells':
+              const: 1
+            '#size-cells':
+              const: 0
+            port@0:
+              type: object
+              description: Input port
+            port@1:
+              type: object
+              description: Output port
+
+          required:
+            - port@1
+
+          additionalProperties: false
+
+      required:
+        - ports
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: adi,adv7612
+    then:
+      properties:
+        ports:
+          properties:
+            '#address-cells':
+              const: 1
+            '#size-cells':
+              const: 0
+            port@2:
+              type: object
+              description: Output port
+
+          patternProperties:
+            "^port@[0-1]$":
+              type: object
+              description: Input port
+
+          required:
+            - port@2
+
+          additionalProperties: false
+
+      required:
+        - ports
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            hdmi_receiver@4c {
+                    compatible = "adi,adv7611";
+                    /*
+                     * The edid page will be accessible @ 0x66 on the I2C bus. All
+                     * other maps will retain their default addresses.
+                     */
+                    reg = <0x4c>, <0x66>;
+                    reg-names = "main", "edid";
+
+                    reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>;
+                    hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>;
+                    default-input = <0>;
+
+                    ports {
+                            #address-cells = <1>;
+                            #size-cells = <0>;
+
+                            port@0 {
+                                    reg = <0>;
+                            };
+
+                            port@1 {
+                                    reg = <1>;
+                                    hdmi_in: endpoint {
+                                            remote-endpoint = <&ccdc_in>;
+                                    };
+                            };
+                    };
+
+
+            };
+    };
-- 
2.27.0




[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux