Hello!
On 06/19/2020 10:15 PM, Geert Uytterhoeven wrote:
> Some EtherAVB variants support internal clock delay configuration, which
> can add larger delays than the delays that are typically supported by
> the PHY (using an "rgmii-*id" PHY mode, and/or "[rt]xc-skew-ps"
> properties).
>
> Add properties for configuring the internal MAC delays.
> These properties are mandatory, even when specified as zero, to
> distinguish between old and new DTBs.
>
> Update the example accordingly.
>
> Signed-off-by: Geert Uytterhoeven <geert+renesas@xxxxxxxxx>
> ---
> .../devicetree/bindings/net/renesas,ravb.txt | 29 ++++++++++---------
> 1 file changed, 16 insertions(+), 13 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt
> index 032b76f14f4fdb38..488ada78b6169b8e 100644
> --- a/Documentation/devicetree/bindings/net/renesas,ravb.txt
> +++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt
> @@ -64,6 +64,18 @@ Optional properties:
> AVB_LINK signal.
> - renesas,ether-link-active-low: boolean, specify when the AVB_LINK signal is
> active-low instead of normal active-high.
> +- renesas,rxc-delay-ps: Internal RX clock delay.
> + This property is mandatory and valid only on R-Car Gen3
> + and RZ/G2 SoCs.
> + Valid values are 0 and 1800.
> + A non-zero value is allowed only if phy-mode = "rgmii".
> + Zero is not supported on R-Car D3.
Hm, where did you see about the D3 limitation?
> +- renesas,txc-delay-ps: Internal TX clock delay.
> + This property is mandatory and valid only on R-Car H3,
> + M3-W, M3-W+, M3-N, V3M, and V3H, and RZ/G2M and RZ/G2N.
> + Valid values are 0 and 2000.
> + A non-zero value is allowed only if phy-mode = "rgmii".
> + Zero is not supported on R-Car V3H.
Same question about V3H here...
[...]
> @@ -105,8 +117,10 @@ Example:
> "ch24";
> clocks = <&cpg CPG_MOD 812>;
> power-domains = <&cpg>;
> - phy-mode = "rgmii-id";
> + phy-mode = "rgmii";
> phy-handle = <&phy0>;
> + renesas,rxc-delay-ps = <0>;
Mhm, zero RX delay in RGMII-ID mode?
> + renesas,txc-delay-ps = <2000>;
>
> pinctrl-0 = <ðer_pins>;
> pinctrl-names = "default";
> @@ -115,18 +129,7 @@ Example:
> #size-cells = <0>;
>
> phy0: ethernet-phy@0 {
> - rxc-skew-ps = <900>;
> - rxdv-skew-ps = <0>;
> - rxd0-skew-ps = <0>;
> - rxd1-skew-ps = <0>;
> - rxd2-skew-ps = <0>;
> - rxd3-skew-ps = <0>;
> - txc-skew-ps = <900>;
> - txen-skew-ps = <0>;
> - txd0-skew-ps = <0>;
> - txd1-skew-ps = <0>;
> - txd2-skew-ps = <0>;
> - txd3-skew-ps = <0>;
> + rxc-skew-ps = <1500>;
Ah, you're relying on a PHY?
[...]
MBR, Sergei
