Re: [PATCH v1 4/4] of: platform: Batch fwnode parsing when adding all top level devices

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Saravana,

On Fri, Jun 19, 2020 at 1:01 AM Saravana Kannan <saravanak@xxxxxxxxxx> wrote:
> On Thu, Jun 18, 2020 at 12:32 AM Geert Uytterhoeven
> <geert@xxxxxxxxxxxxxx> wrote:
> > On Wed, Jun 17, 2020 at 8:36 PM Saravana Kannan <saravanak@xxxxxxxxxx> wrote:
> > > On Wed, Jun 17, 2020 at 5:20 AM Geert Uytterhoeven <geert@xxxxxxxxxxxxxx> wrote:
> > > > On Fri, May 15, 2020 at 7:38 AM Saravana Kannan <saravanak@xxxxxxxxxx> wrote:
> > > > > The fw_devlink_pause() and fw_devlink_resume() APIs allow batching the
> > > > > parsing of the device tree nodes when a lot of devices are added. This
> > > > > will significantly cut down parsing time (as much a 1 second on some
> > > > > systems). So, use them when adding devices for all the top level device
> > > > > tree nodes in a system.
> > > > >
> > > > > Signed-off-by: Saravana Kannan <saravanak@xxxxxxxxxx>
> > > >
> > > > This is now commit 93d2e4322aa74c1a ("of: platform: Batch fwnode parsing
> > > > when adding all top level devices") in v5.8-rc1, and I have bisected a
> > > > regression to it: on r8a7740/armadillo and sh73a0/kzm9g, the system can
> > > > no longer be woken up from s2ram by a GPIO key. Reverting the commit
> > > > fixes the issue.
> > > >
> > > > On these systems, the GPIO/PFC block has its interrupt lines connected
> > > > to intermediate interrupt controllers (Renesas INTC), which are in turn
> > > > connected to the main interrupt controller (ARM GIC).  The INTC block is
> > > > part of a power and clock domain.  Hence if a GPIO is enabled as a
> > > > wake-up source, the INTC is part of the wake-up path, and thus must be
> > > > kept enabled when entering s2ram.
> > > >
> > > > While this commit has no impact on probe order for me (unlike in Marek's
> > > > case), it does have an impact on suspend order:
> > > >   - Before this commit:
> > > >       1. The keyboard (gpio-keys) is suspended, and calls
> > > >          enable_irq_wake() to inform the upstream interrupt controller
> > > >          (INTC) that it is part of the wake-up path,
> > > >       2. INTC is suspended, and calls device_set_wakeup_path() to inform
> > > >          the device core that it must be kept enabled,
> > > >       3. The system is woken by pressing a wake-up key.
> > > >
> > > >   - After this commit:
> > > >       1. INTC is suspended, and is not aware it is part of the wake-up
> > > >          path, so it is disabled by the device core,
> > > >       2. gpio-keys is suspended, and calls enable_irq_wake() in vain,
> > > >       3. Pressing a wake-up key has no effect, as INTC is disabled, and
> > > >          the interrupt does not come through.
> > > >
> > > > It looks like no device links are involved, as both gpio-keys and INTC have
> > > > no links.
> > > > Do you have a clue?
> > > >
> > > > Thanks!
> > >
> > > That patch of mine defers probe on all devices added by the
> > > of_platform_default_populate() call, and then once the call returns,
> > > it immediately triggers a deferred probe.
> > >
> > > So all these devices are being probed in parallel in the deferred
> > > probe workqueue while the main "initcall thread" continues down to
> > > further initcalls. It looks like some of the drivers in subsequent
> > > initcalls are assuming that devices in the earlier initcalls always
> > > probe and can't be deferred?
> > >
> > > There are two options.
> > > 1. Fix these drivers.
> > > 2. Add a "flush deferred workqueue" in fw_devlink_resume()
> > >
> > > I'd rather we fix the drivers so that they handle deferred probes
> > > correctly. Thoughts?
> >
> > While the affected drivers should handle deferred probe fine, none of
> > the affected drivers is subject to deferred probing: they all probe
> > successfully on first try (I had added debug prints to
> > platform_drv_probe() to be sure).
> > The affected drivers are still probed in the same order (INTC is one of
> > the earliest drivers probed, gpio-keys is the last).
>
> Thanks, this is useful info. Now I know that my patch isn't somehow
> reordering devices that would have probed as soon as
> of_platform_default_populate_init() added them.
>
> When you say the "The affected drivers are still probed in the same
> order", are you only referring to the devices that would have probed
> before of_platform_default_populate_init() returns? Or ALL devices in
> the system are probing in the same order?

I was referring to all platform devices (based on a debug print added to
platform_drv_probe()). See more below.

> I assume gpio-keys gets probed in the "normal init thread" and not by
> the deferred probe workqueue? I'm guessing this because gpio_keys
> driver seems to register during late_initcall() whereas
> of_platform_default_populate_init() runs as an arch_initcall_sync().

After adding a WARN(1, ...) to gpio_keys_probe(), the backtrace shows it
is called directly from do_one_initcall(), in both the good and the bad
case.

> > However, during
> > system suspend, gpio-keys is suspended before INTC, which is wrong, as
> > gpio-keys uses an interrupt provided by INTC.
> >
> > Perhaps the "in parallel" is the real culprit, and there is a race
> > condition somewhere?
>
> I tried digging into the gpio_keys driver code to see how it interacts
> with INTC and if gpio-keys defers probe if INTC hasn't probed yet. But
> it seems like a rabbit hole that'd be easier to figure out when you
> have the device. Can you check if gpio-keys is probing before INTC in
> the "bad" case?

It is not, gpio-keys is always probed very late.

Hence for testing, I moved gpio-keys initialization just before INTC, so
it is probed before INTC. Then gpio-keys is deferred, as expected, and
reprobes successfully later.
Interestingly, that fixes my wake-up issue, too?!?

> Also, in general, can you see if there's a difference in the probe
> order between all the devices in the system? Adding a log to
> really_probe() would be better in case non-platform devices are
> getting reordered (my change affects all devices that are created from
> DT, not just platform devices).
>
> I want to make sure we understand the real issue before we try to fix it.

Enabling all debug prints in really_probe(), comparing the output
before/after the bad commit, and filtering out all noise, I get:

     bus: 'platform': really_probe: probing driver reg-dummy with
device reg-dummy
B    bus: 'platform': really_probe: probing driver renesas_intc_irqpin
with device e6900000.interrupt-controller
     bus: 'platform': really_probe: probing driver renesas_intc_irqpin
with device e6900004.interrupt-controller
A   +Workqueue: events deferred_probe_work_func
     bus: 'platform': really_probe: probing driver renesas_intc_irqpin
with device e6900008.interrupt-controller
C    bus: 'platform': really_probe: probing driver renesas_intc_irqpin
with device e690000c.interrupt-controller
     bus: 'platform': really_probe: probing driver sh-pfc with device
e6050000.pin-controller
     bus: 'platform': really_probe: probing driver reg-fixed-voltage
with device regulator-1p8v
     bus: 'platform': really_probe: probing driver reg-fixed-voltage
with device regulator-3p3v
     bus: 'platform': really_probe: probing driver reg-fixed-voltage
with device regulator-vmmc-sdhi0
     bus: 'platform': really_probe: probing driver reg-fixed-voltage
with device regulator-vmmc-sdhi2
     bus: 'platform': really_probe: probing driver i2c-sh_mobile with
device e6820000.i2c
     bus: 'i2c': really_probe: probing driver as3711 with device 0-0040
     bus: 'platform': really_probe: probing driver as3711-regulator
with device as3711-regulator
     bus: 'platform': really_probe: probing driver i2c-sh_mobile with
device e6822000.i2c
     bus: 'platform': really_probe: probing driver i2c-sh_mobile with
device e6826000.i2c
     bus: 'i2c': really_probe: probing driver pcf857x with device 2-0020
     bus: 'platform': really_probe: probing driver sh_cmt with device
e6138000.timer
     bus: 'platform': really_probe: probing driver armv7-pmu with device pmu
     bus: 'platform': really_probe: probing driver simple-pm-bus with
device fec10000.bus
     bus: 'platform': really_probe: probing driver as3711-backlight
with device as3711-backlight
     bus: 'platform': really_probe: probing driver sh-sci with device
e6c80000.serial
     bus: 'platform': really_probe: probing driver smsc911x with
device 10000000.ethernet
     bus: 'i2c': really_probe: probing driver st1232-ts with device 1-0055
     bus: 'i2c': really_probe: probing driver adxl34x with device 0-001d
     bus: 'i2c': really_probe: probing driver rtc-rs5c372 with device 0-0032
     bus: 'platform': really_probe: probing driver rmobile_reset with
device e6180000.system-controller
     bus: 'platform': really_probe: probing driver cpufreq-dt with
device cpufreq-dt
     bus: 'platform': really_probe: probing driver sh_mobile_sdhi with
device ee100000.sd
     bus: 'platform': really_probe: probing driver sh_mobile_sdhi with
device ee140000.sd
     bus: 'platform': really_probe: probing driver sh_mmcif with
device e6bd0000.mmc
     bus: 'platform': really_probe: probing driver leds-gpio with device leds
     bus: 'i2c': really_probe: probing driver ak8975 with device 0-000c
     bus: 'platform': really_probe: probing driver snd-soc-dummy with
device snd-soc-dummy
     bus: 'i2c': really_probe: probing driver ak4642-codec with device 0-0012
     bus: 'platform': really_probe: probing driver asoc-simple-card
with device sound
     bus: 'platform': really_probe: probing driver fsi-pcm-audio with
device ec230000.sound
     bus: 'platform': really_probe: probing driver asoc-simple-card
with device sound
     bus: 'platform': really_probe: probing driver gpio-keys with
device keyboard"
     bus: 'mmc': really_probe: probing driver mmcblk with device mmc2:0001

So all devices are probed in the exact same order.
A: Note the addition of the message "Workqueue: events
   deferred_probe_work_func", which might give a clue?
B,C: "e6900000.interrupt-controller" and "e6900008.interrupt-controller"
     are the two devices that are suspended later in the wrong order.
     One of them is probed before A, one after, so A may be a red herring?

I'm still not much wiser, though....

BTW, r8a7740/armadillo is single CPU, while sh73a0/kzm9g is dual-CPU.
So both UP and SMP are affected.

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds



[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux