Hi Prabhakar,
On Sun, Mar 22, 2020 at 3:13 PM Lad Prabhakar
<prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx> wrote:
> This patch adds support for AISTARVISION MIPI Adapter V2.1 board connected
> to G2E board. Common file aistarvision-mipi-adapter-2.1.dtsi is created
> which have the camera endpoint nodes for imx219 and ov5645 so that this can
> be re-used with other G2x platforms.
>
> r8a774c0-ek874-mipi-2.1.dts file enables the required VIN/CSI nodes and by
> default ties ov5645 camera endpoint to CSI2.
>
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> ---
> Changes for v2:
> * Dropped #{address,size}-cells
> * Dropped unit address and reg for port
Thanks for the update!
> --- /dev/null
> +++ b/arch/arm64/boot/dts/renesas/r8a774c0-ek874-mipi-2.1.dts
> @@ -0,0 +1,75 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Device Tree Source for the Silicon Linux RZ/G2E 96board platform (CAT874)
> + * connected with aistarvision-mipi-v2-adapter board
> + *
> + * Copyright (C) 2020 Renesas Electronics Corp.
> + */
> +
> +/dts-v1/;
> +#include "r8a774c0-ek874.dts"
> +#define MIPI_PARENT_I2C i2c3
> +#include "aistarvision-mipi-adapter-2.1.dtsi"
> +
> +/ {
> + model = "Silicon Linux RZ/G2E evaluation kit EK874 (CAT874 + CAT875) with aistarvision-mipi-v2-adapter board";
> + compatible = "si-linux,cat875", "si-linux,cat874", "renesas,r8a774c0";
> +};
> +
> +&i2c3 {
> + status = "okay";
> +};
> +
> +&vin4 {
> + status = "okay";
> +};
> +
> +&vin5 {
> + status = "okay";
> +};
> +
> +&csi40 {
> + status = "okay";
> +
> + ports {
> + port {
> + csi40_in: endpoint {
> + clock-lanes = <0>;
> + data-lanes = <1 2>;
> + remote-endpoint = <&ov5645_ep>;
> + };
> + };
> + };
> +};
> +
> +&ov5645 {
> + enable-gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>;
> + reset-gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
> +
> + clocks = <&cpg CPG_MOD 716>;
I'm still a bit puzzled here.
CPG_MOD 716 is the CSI40 module clock, which runs at 25 MHz, and is
presumably output to the CSI0_CLKP/N pair? Or is its rate controlled
by the CSI driver?
On the MIPI board[*], that signal becomes MIPI1_CP/N.
However, the MIPI board also has a "Clock Source Selection" header,
which allows you to choose one of:
1. The fixed 24 MHz crystal, which is apparently used for the imx219
camera, as described by imx219_clk above, and matches the wanted
clock rate specified below?
2. CSI1_CLK,
3. CSI2_CLK.
The last two become CLK0/1 on the CAT874 board, which are driven by
TPU0TO0/1.
Which setting do you use for the ov5645 camera?
> + clock-frequency = <24000000>;
After your patch for the ov5645 driver, this should be replaced by
assigned-clock-rates?
The rest looks good to me, but I'm not a multi-media/camera expert.
[*] https://github.com/Kevin-WSCU/96Boards-Camera
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
