On Tue, Mar 10, 2020 at 5:47 PM Florian Fainelli <f.fainelli@xxxxxxxxx> wrote:
>
> On 3/10/20 7:16 AM, Geert Uytterhoeven wrote:
> > Hi Florian, David,
> >
> > On Mon, Feb 24, 2020 at 5:59 AM David Miller <davem@xxxxxxxxxxxxx> wrote:
> >> From: Florian Fainelli <f.fainelli@xxxxxxxxx>
> >> Date: Thu, 20 Feb 2020 15:34:53 -0800
> >>
> >>> It is currently possible for a PHY device to be suspended as part of a
> >>> network device driver's suspend call while it is still being attached to
> >>> that net_device, either via phy_suspend() or implicitly via phy_stop().
> >>>
> >>> Later on, when the MDIO bus controller get suspended, we would attempt
> >>> to suspend again the PHY because it is still attached to a network
> >>> device.
> >>>
> >>> This is both a waste of time and creates an opportunity for improper
> >>> clock/power management bugs to creep in.
> >>>
> >>> Fixes: 803dd9c77ac3 ("net: phy: avoid suspending twice a PHY")
> >>> Signed-off-by: Florian Fainelli <f.fainelli@xxxxxxxxx>
> >>
> >> Applied, and queued up for -stable, thanks Florian.
> >
> > This patch causes a regression on r8a73a4/ape6evm and sh73a0/kzm9g.
> > After resume from s2ram, Ethernet no longer works:
> >
> > PM: suspend exit
> > nfs: server aaa.bbb.ccc.ddd not responding, still trying
> > ...
> >
> > Reverting commit 503ba7c6961034ff ("net: phy: Avoid multiple suspends")
> > fixes the issue.
> >
> > On both boards, an SMSC LAN9220 is connected to a power-managed local
> > bus.
> >
> > I added some debug code to check when the clock driving the local bus
> > is stopped and started, but I see no difference before/after. Hence I
> > suspect the Ethernet chip is no longer reinitialized after resume.
>
> Can you provide a complete log?
With some debug info:
SDHI0 Vcc: disabling
PM: suspend entry (deep)
Filesystems sync: 0.002 seconds
Freezing user space processes ... (elapsed 0.001 seconds) done.
OOM killer disabled.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
PM: ==== a3sp/ee120000.sd: stop
PM: ==== a3sp/ee100000.sd: stop
smsc911x 8000000.ethernet: smsc911x_suspend:2577
smsc911x 8000000.ethernet: smsc911x_suspend:2579 running
smsc911x 8000000.ethernet: smsc911x_suspend:2584
PM: ==== a3sp/ee200000.mmc: stop
PM: ==== c4/fec10000.bus: stop
PM: ==== a3sp/e6c40000.serial: stop
PM: ==== c5/e61f0000.thermal: stop
PM: ==== c4/e61c0200.interrupt-controller: stop
PM: == a3sp: power off
rmobile_pd_power_down: a3sp
Disabling non-boot CPUs ...
PM: ==== c4/e61c0200.interrupt-controller: start
PM: ==== c5/e61f0000.thermal: start
PM: ==== a3sp/e6c40000.serial: start
PM: ==== c4/fec10000.bus: start
PM: ==== a3sp/ee200000.mmc: start
smsc911x 8000000.ethernet: smsc911x_resume:2606
smsc911x 8000000.ethernet: smsc911x_resume:2625 running
PM: ==== a3sp/ee100000.sd: start
OOM killer enabled.
Restarting tasks ... done.
PM: ==== a3sp/ee120000.sd: start
PM: suspend exit
nfs: server aaa.bbb.ccc.ddd not responding, still trying
...
But no difference between the good and the bad case, except for the nfs
failures.
> Do you use the Generic PHY driver or a
> specialized one?
CONFIG_FIXED_PHY=y
CONFIG_SMSC_PHY=y
Just the smsc,lan9115 node, cfr. arch/arm/boot/dts/r8a73a4-ape6evm.dts
> Do you have a way to dump the registers at the time of
> failure and see if BMCR.PDOWN is still set somehow?
Added a hook into "nfs: server not responding", which prints:
MII_BMCR = 0x1900
i.e. BMCR_PDOWN = 0x0800 is still set.
> Does the following help:
>
> diff --git a/drivers/net/ethernet/smsc/smsc911x.c
> b/drivers/net/ethernet/smsc/smsc911x.c
> index 49a6a9167af4..df17190c76c0 100644
> --- a/drivers/net/ethernet/smsc/smsc911x.c
> +++ b/drivers/net/ethernet/smsc/smsc911x.c
> @@ -2618,6 +2618,7 @@ static int smsc911x_resume(struct device *dev)
> if (netif_running(ndev)) {
> netif_device_attach(ndev);
> netif_start_queue(ndev);
> + phy_resume(dev->phydev);
> }
>
Yes i does, after s/dev->/ndev->/.
Thanks!
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
