Hi Alex,
On Mon, Mar 2, 2020 at 4:07 PM Alex Riesen <alexander.riesen@xxxxxxxxxxx> wrote:
> Geert Uytterhoeven, Mon, Mar 02, 2020 14:47:46 +0100:
> > On Mon, Mar 2, 2020 at 2:40 PM Alex Riesen <alexander.riesen@xxxxxxxxxxx> wrote:
> > > > > --- a/arch/arm64/boot/dts/renesas/salvator-common.dtsi
> > > > > +++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
> > > > > @@ -322,6 +322,10 @@
> > > > > clock-frequency = <22579200>;
> > > > > };
> > > > >
> > > > > +&audio_clk_c {
> > > > > + clock-frequency = <12288000>;
> > > > > +};
> > > >
> > > > Does the ADV7482 always generate a 12.288 MHz clock signal?
> > > > Or is this programmable?
> > >
> > > Oops. It looks like it is and the value is derived from the sampling rate
> > > (48kHz) and the master clock multiplier. Both hard-coded in the board file.
> >
> > Where are these hardcoded in the board file?
>
> In the endpoint definition, arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dts
>
> So the frequency can be set at the run-time, perhaps even derived from
> endpoint connected to the output. In this case, rsnd_endpoint3,
> which has the "mclk-fs" setting. Not sure if the sampling rate
> can be set to something else for the HDMI, though.
>
> > Even if they are, technically this is a clock output of the ADV7482.
>
> ... which I hope to correct as soon as I steal the hardware from whoever stole
> it from me...
>
> > > > > video-receiver@70 {
> > > > > compatible = "adi,adv7482";
> > > > > ...
> > > > > + clocks = <&rcar_sound 3>, <&audio_clk_c>;
> > > > > + clock-names = "clk-hdmi-video", "clk-hdmi-i2s-mclk";
> > > >
> > > > The above declares the Audio CLK C to be a clock input of the ADV7482, while
> > > > it is an output.
> > >
> > > I would gladly give it right direction if I *really* understood what I was
> > > doing...
> >
> > :-)
> >
> > > > Furthermore, the DT bindings do not document that clocks can be specified.
> > >
> > > Should the DT bindings document that the clock cannot be specified than?
> >
> > It currently does say so, as it doesn't list "clocks" in its properties section.
>
> The bindings documentation file, which we're talking about here and which does
> not list the specifiable input clocks in its properties, is it the
>
> Documentation/devicetree/bindings/media/i2c/adv748x.txt
>
> ?
Yes.
>
> And this absence of documentation also means that whatever clocks (both input
> in "clocks=" and output in "#clock-cells") listed in a specific .dts are just
> an integration detail?
No, the absence probably means that any clock-related properties in a .dts
file will just be ignored.
Looking at the driver source, it indeed has no support related to clocks at all.
> Does this below makes more sense, than?
>
> video-receiver@70 {
> compatible = "adi,adv7482";
> clocks = <&rcar_sound 3>;
> clock-names = "clk-hdmi-video";
> adv748x_mclk: mclk {
> compatible = "fixed-clock";
> #clock-cells = <0>;
> /* frequency hard-coded for illustration */
> clock-frequency = <12288000>;
> clock-output-names = "clk-hdmi-i2s-mclk";
> };
> };
The #clock-cells should be in the main video-receiver node.
Probably there is more than one clock output, so #clock-cells may be 1?
There is no need for a fixed-clock compatible, nor for clock-frequency
and clock-output-names.
But most important: this should be documented in the adv748x DT bindings,
and implemented in the adv748x driver.
> Now I'm a bit hazy on how to declare that the MCLK output of the
> video-receiver@70 is connected to the Audio Clock C of the SoC...
> Probably remove use of "audio_clk_c" completely?
Yes, the current audio_clk_c definition in the DTS assumes a fixed
crystal.
> > > > > @@ -686,7 +700,8 @@
> > > > > };
> > > > >
> > > > > sound_pins: sound {
> > > > > - groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
> > > > > + groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a",
> > > > > + "ssi4_data";
> > > >
> > > > Missing "ss4_ctrl", for the SCK4 and WS4 pins.
> > >
> > > I'll add them.
> > > As the device seems to function even without thoes, does this mean the
> > > pins in the group are used "on demand" by whatever needs them?
> >
> > Probably the SCK4/WS4 functions are the reset-state defaults.
>
> That ... might require some trial and testing: when I add them to the group,
> the reset defaults will be overridden by the platform initialization, which is
> not necessarily the reset default. Will see.
Or by the boot loader. Anyway, you need to specify these in the DTS.
> > > Does a "clocks = ..." statement always mean input clocks?
> >
> > Yes it does.
> > If a device has clock outputs and is thus a clock provider, it should
> > have a #clock-cells property, and this should be documented in the bindings.
> >
> > A clock consumer will refer to clocks of a provider using the "clocks"
> > property, specifying a clock specifier (phandle and zero or more indices)
> > for each clock referenced.
>
> Something like this?
>
> &rcar_sound {
> clocks = ...,
> <&adv748x_mclk>,
> <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
> clock-names = ...,
> "clk_c",
> "clk_i";
> };
More or less.
Might become
find_a_better_label_choice: video-receiver@70 {
...
};
&rcar_sound {
clock = ...,
<&find_a_better_label_choice 0>,
...
};
as there may be multiple clock outputs on the ADV7482.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
