[PATCH v4 0/5] gpio: Add GPIO Aggregator

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



	Hi all,

GPIO controllers are exported to userspace using /dev/gpiochip*
character devices.  Access control to these devices is provided by
standard UNIX file system permissions, on an all-or-nothing basis:
either a GPIO controller is accessible for a user, or it is not.
Currently no mechanism exists to control access to individual GPIOs.

Hence this adds a GPIO driver to aggregate existing GPIOs, and expose
them as a new gpiochip.  This is useful for implementing access control,
and assigning a set of GPIOs to a specific user.  Furthermore, this
simplifies and hardens exporting GPIOs to a virtual machine, as the VM
can just grab the full GPIO controller, and no longer needs to care
about which GPIOs to grab and which not, reducing the attack surface.

Recently, other use cases have been discovered[1]:
  - Describing simple GPIO-operated devices in DT, and using the GPIO
    Aggregator as a generic GPIO driver for userspace, which is useful
    for industrial control.

Changes compared to v3[2] (more details in the individual patches):
  - Drop controversial GPIO repeater,
  - Drop support for legacy sysfs interface based name matching,
  - Drop applied "gpiolib: Add GPIOCHIP_NAME definition",
  - Documentation improvements,
  - Lots of small cleanups.

Changes compared to v2[3] (more details in the individual patches):
  - Integrate GPIO Repeater functionality,
  - Absorb GPIO forwarder library, as the Aggregator and Repeater are
    now a single driver,
  - Use the aggregator parameters to create a GPIO lookup table instead
    of an array of GPIO descriptors,
  - Add documentation,
  - New patches:
      - "gpiolib: Add GPIOCHIP_NAME definition",
      - "gpiolib: Add support for gpiochipN-based table lookup",
      - "gpiolib: Add support for GPIO line table lookup",
      - "dt-bindings: gpio: Add gpio-repeater bindings",
      - "docs: gpio: Add GPIO Aggregator/Repeater documentation",
      - "MAINTAINERS: Add GPIO Aggregator/Repeater section".
  - Dropped patches:
      - "gpio: Export gpiod_{request,free}() to modular GPIO code",
      - "gpio: Export gpiochip_get_desc() to modular GPIO code",
      - "gpio: Export gpio_name_to_desc() to modular GPIO code",
      - "gpio: Add GPIO Forwarder Helper".

Changes compared to v1[4]:
  - Drop "virtual", rename to gpio-aggregator,
  - Create and use new GPIO Forwarder Helper, to allow sharing code with
    the GPIO inverter,
  - Lift limit on the maximum number of GPIOs,
  - Improve parsing of GPIO specifiers,
  - Fix modular build.

Aggregating GPIOs and exposing them as a new gpiochip was suggested in
response to my proof-of-concept for GPIO virtualization with QEMU[5][6].

For the first use case, aggregated GPIO controllers are instantiated and
destroyed by writing to atribute files in sysfs.
Sample session on the Renesas Koelsch development board:

  - Unbind LEDs from leds-gpio driver:

        echo leds > /sys/bus/platform/drivers/leds-gpio/unbind

  - Create aggregators:

    $ echo e6052000.gpio 19,20 \
        > /sys/bus/platform/drivers/gpio-aggregator/new_device

    gpio-aggregator gpio-aggregator.0: gpio 0 => gpio-953 (gpio-aggregator.0)
    gpio-aggregator gpio-aggregator.0: gpio 1 => gpio-954 (gpio-aggregator.0)
    gpiochip_find_base: found new base at 778
    gpio gpiochip8: (gpio-aggregator.0): added GPIO chardev (254:8)
    gpiochip_setup_dev: registered GPIOs 778 to 779 on device: gpiochip8 (gpio-aggregator.0)

    $ echo e6052000.gpio 21 e6050000.gpio 20-22 \
        > /sys/bus/platform/drivers/gpio-aggregator/new_device

    gpio-aggregator gpio-aggregator.1: gpio 0 => gpio-955 (gpio-aggregator.1)
    gpio-aggregator gpio-aggregator.1: gpio 1 => gpio-1012 (gpio-aggregator.1)
    gpio-aggregator gpio-aggregator.1: gpio 2 => gpio-1013 (gpio-aggregator.1)
    gpio-aggregator gpio-aggregator.1: gpio 3 => gpio-1014 (gpio-aggregator.1)
    gpiochip_find_base: found new base at 774
    gpio gpiochip9: (gpio-aggregator.1): added GPIO chardev (254:9)
    gpiochip_setup_dev: registered GPIOs 774 to 777 on device: gpiochip9 (gpio-aggregator.1)

  - Adjust permissions on /dev/gpiochip[89] (optional)

  - Control LEDs:

    $ gpioset gpiochip8 0=0 1=1 # LED6 OFF, LED7 ON
    $ gpioset gpiochip8 0=1 1=0 # LED6 ON, LED7 OFF
    $ gpioset gpiochip9 0=0     # LED8 OFF
    $ gpioset gpiochip9 0=1     # LED8 ON

  - Destroy aggregators:

    $ echo gpio-aggregator.0 \
            > /sys/bus/platform/drivers/gpio-aggregator/delete_device
    $ echo gpio-aggregator.1 \
            > /sys/bus/platform/drivers/gpio-aggregator/delete_device

Thanks!

References:
  [1] "[PATCH V4 2/2] gpio: inverter: document the inverter bindings"
      (https://lore.kernel.org/linux-gpio/1561699236-18620-3-git-send-email-harish_kandiga@xxxxxxxxxx/)
  [2] "[PATCH v3 0/7] gpio: Add GPIO Aggregator/Repeater"
      (https://lore.kernel.org/lkml/20191127084253.16356-1-geert+renesas@xxxxxxxxx/)
  [3] "[PATCH/RFC v2 0/5] gpio: Add GPIO Aggregator Driver"
      (https://lore.kernel.org/linux-gpio/20190911143858.13024-1-geert+renesas@xxxxxxxxx/)
  [4] "[PATCH RFC] gpio: Add Virtual Aggregator GPIO Driver"
      (https://lore.kernel.org/lkml/20190705160536.12047-1-geert+renesas@xxxxxxxxx/)
  [5] "[PATCH QEMU POC] Add a GPIO backend"
      (https://lore.kernel.org/linux-renesas-soc/20181003152521.23144-1-geert+renesas@xxxxxxxxx/)
  [6] "Getting To Blinky: Virt Edition / Making device pass-through
       work on embedded ARM"
      (https://fosdem.org/2019/schedule/event/vai_getting_to_blinky/)

Geert Uytterhoeven (5):
  gpiolib: Add support for gpiochipN-based table lookup
  gpiolib: Add support for GPIO line table lookup
  gpio: Add GPIO Aggregator
  docs: gpio: Add GPIO Aggregator documentation
  MAINTAINERS: Add GPIO Aggregator section

 .../admin-guide/gpio/gpio-aggregator.rst      | 102 ++++
 Documentation/admin-guide/gpio/index.rst      |   1 +
 MAINTAINERS                                   |   7 +
 drivers/gpio/Kconfig                          |  12 +
 drivers/gpio/Makefile                         |   1 +
 drivers/gpio/gpio-aggregator.c                | 574 ++++++++++++++++++
 drivers/gpio/gpiolib.c                        |  33 +-
 include/linux/gpio/machine.h                  |  15 +-
 8 files changed, 732 insertions(+), 13 deletions(-)
 create mode 100644 Documentation/admin-guide/gpio/gpio-aggregator.rst
 create mode 100644 drivers/gpio/gpio-aggregator.c

-- 
2.17.1

Gr{oetje,eeting}s,

						Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
							    -- Linus Torvalds



[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux