Currently the st7735r driver supports only a single display panel.
Prepare for adding support for other display panels by factoring out the
display-specific parameters in struct st7735r_cfg.
For now, the following parameters can be configured:
- Display resolution,
- Horizontal/vertical display offsets,
- Read-write versus read-only controllers,
- RGB versus BGR color component ordering.
Rename jd_t18003_t01_pipe_enable() and jd_t18003_t01_pipe_funcs() to
st7735r_pipe_enable() resp. st7735r_pipe_funcs(), as they are not really
specific to the Jianda JD-T18003-T01 display anymore.
Signed-off-by: Geert Uytterhoeven <geert+renesas@xxxxxxxxx>
---
v2:
- Split off from "drm: tiny: st7735r: Add support for Okaya
RH128128T",
- Replace st7735r_priv.rgb by a pointer to struct st7735r_cfg,
- Change prefix of jd_t18003_t01_pipe_enable() and
jd_t18003_t01_pipe_funcs().
---
drivers/gpu/drm/tiny/st7735r.c | 67 +++++++++++++++++++++++++++-------
1 file changed, 53 insertions(+), 14 deletions(-)
diff --git a/drivers/gpu/drm/tiny/st7735r.c b/drivers/gpu/drm/tiny/st7735r.c
index 3f4487c716848cf8..a838f237c8d82e3d 100644
--- a/drivers/gpu/drm/tiny/st7735r.c
+++ b/drivers/gpu/drm/tiny/st7735r.c
@@ -3,6 +3,7 @@
* DRM driver for Sitronix ST7735R panels
*
* Copyright 2017 David Lechner <david@xxxxxxxxxxxxxx>
+ * Copyright (C) 2019 Glider bvba
*/
#include <linux/backlight.h>
@@ -10,6 +11,7 @@
#include <linux/dma-buf.h>
#include <linux/gpio/consumer.h>
#include <linux/module.h>
+#include <linux/of_device.h>
#include <linux/property.h>
#include <linux/spi/spi.h>
#include <video/mipi_display.h>
@@ -37,12 +39,28 @@
#define ST7735R_MY BIT(7)
#define ST7735R_MX BIT(6)
#define ST7735R_MV BIT(5)
+#define ST7735R_RGB BIT(3)
+
+struct st7735r_cfg {
+ const struct drm_display_mode mode;
+ unsigned int left_offset;
+ unsigned int top_offset;
+ unsigned int write_only:1;
+ unsigned int rgb:1; /* RGB (vs. BGR) */
+};
+
+struct st7735r_priv {
+ struct mipi_dbi_dev dbidev; /* Must be first for .release() */
+ const struct st7735r_cfg *cfg;
+};
-static void jd_t18003_t01_pipe_enable(struct drm_simple_display_pipe *pipe,
- struct drm_crtc_state *crtc_state,
- struct drm_plane_state *plane_state)
+static void st7735r_pipe_enable(struct drm_simple_display_pipe *pipe,
+ struct drm_crtc_state *crtc_state,
+ struct drm_plane_state *plane_state)
{
struct mipi_dbi_dev *dbidev = drm_to_mipi_dbi_dev(pipe->crtc.dev);
+ struct st7735r_priv *priv = container_of(dbidev, struct st7735r_priv,
+ dbidev);
struct mipi_dbi *dbi = &dbidev->dbi;
int ret, idx;
u8 addr_mode;
@@ -87,6 +105,10 @@ static void jd_t18003_t01_pipe_enable(struct drm_simple_display_pipe *pipe,
addr_mode = ST7735R_MY | ST7735R_MV;
break;
}
+
+ if (priv->cfg->rgb)
+ addr_mode |= ST7735R_RGB;
+
mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, addr_mode);
mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT,
MIPI_DCS_PIXEL_FMT_16BIT);
@@ -109,15 +131,19 @@ static void jd_t18003_t01_pipe_enable(struct drm_simple_display_pipe *pipe,
drm_dev_exit(idx);
}
-static const struct drm_simple_display_pipe_funcs jd_t18003_t01_pipe_funcs = {
- .enable = jd_t18003_t01_pipe_enable,
+static const struct drm_simple_display_pipe_funcs st7735r_pipe_funcs = {
+ .enable = st7735r_pipe_enable,
.disable = mipi_dbi_pipe_disable,
.update = mipi_dbi_pipe_update,
.prepare_fb = drm_gem_fb_simple_display_pipe_prepare_fb,
};
-static const struct drm_display_mode jd_t18003_t01_mode = {
- DRM_SIMPLE_MODE(128, 160, 28, 35),
+static const struct st7735r_cfg jd_t18003_t01_cfg = {
+ .mode = { DRM_SIMPLE_MODE(128, 160, 28, 35) },
+ /* Cannot read from Adafruit 1.8" display via SPI */
+ .write_only = true,
+};
+
};
DEFINE_DRM_GEM_CMA_FOPS(st7735r_fops);
@@ -136,13 +162,13 @@ static struct drm_driver st7735r_driver = {
};
static const struct of_device_id st7735r_of_match[] = {
- { .compatible = "jianda,jd-t18003-t01" },
+ { .compatible = "jianda,jd-t18003-t01", .data = &jd_t18003_t01_cfg },
{ },
};
MODULE_DEVICE_TABLE(of, st7735r_of_match);
static const struct spi_device_id st7735r_id[] = {
- { "jd-t18003-t01", 0 },
+ { "jd-t18003-t01", (uintptr_t)&jd_t18003_t01_cfg },
{ },
};
MODULE_DEVICE_TABLE(spi, st7735r_id);
@@ -150,17 +176,26 @@ MODULE_DEVICE_TABLE(spi, st7735r_id);
static int st7735r_probe(struct spi_device *spi)
{
struct device *dev = &spi->dev;
+ const struct st7735r_cfg *cfg;
struct mipi_dbi_dev *dbidev;
+ struct st7735r_priv *priv;
struct drm_device *drm;
struct mipi_dbi *dbi;
struct gpio_desc *dc;
u32 rotation = 0;
int ret;
- dbidev = kzalloc(sizeof(*dbidev), GFP_KERNEL);
- if (!dbidev)
+ cfg = of_device_get_match_data(&spi->dev);
+ if (!cfg)
+ cfg = (void *)spi_get_device_id(spi)->driver_data;
+
+ priv = kzalloc(sizeof(*priv), GFP_KERNEL);
+ if (!priv)
return -ENOMEM;
+ dbidev = &priv->dbidev;
+ priv->cfg = cfg;
+
dbi = &dbidev->dbi;
drm = &dbidev->drm;
ret = devm_drm_dev_init(dev, drm, &st7735r_driver);
@@ -193,10 +228,14 @@ static int st7735r_probe(struct spi_device *spi)
if (ret)
return ret;
- /* Cannot read from Adafruit 1.8" display via SPI */
- dbi->read_commands = NULL;
+ if (cfg->write_only)
+ dbi->read_commands = NULL;
+
+ dbidev->left_offset = cfg->left_offset;
+ dbidev->top_offset = cfg->top_offset;
- ret = mipi_dbi_dev_init(dbidev, &jd_t18003_t01_pipe_funcs, &jd_t18003_t01_mode, rotation);
+ ret = mipi_dbi_dev_init(dbidev, &st7735r_pipe_funcs, &cfg->mode,
+ rotation);
if (ret)
return ret;
--
2.17.1
