Enable low-level debugging support for RZ/A2M (r7s9210). The RZA2MEVB board uses either SCIF2 (SDRAM enabled) or SCIF4 (HyperRAM only) for the serial console. Note that "SCIFA" serial ports on RZ/A2 SoCs use a compressed register layout, hence add support for that to renesas-scif.S. Signed-off-by: Geert Uytterhoeven <geert+renesas@xxxxxxxxx> --- arch/arm/Kconfig.debug | 20 +++++++++++++++++++- arch/arm/include/debug/renesas-scif.S | 6 +++++- 2 files changed, 24 insertions(+), 2 deletions(-) diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug index 85710e078afb4878..9fe038aecc553deb 100644 --- a/arch/arm/Kconfig.debug +++ b/arch/arm/Kconfig.debug @@ -924,6 +924,20 @@ choice Say Y here if you want kernel low-level debugging support via SCIF2 on Renesas RZ/A1H (R7S72100). + config DEBUG_R7S9210_SCIF2 + bool "Kernel low-level debugging messages via SCIF2 on R7S9210" + depends on ARCH_R7S9210 + help + Say Y here if you want kernel low-level debugging support + via SCIF2 on Renesas RZ/A2M (R7S9210). + + config DEBUG_R7S9210_SCIF4 + bool "Kernel low-level debugging messages via SCIF4 on R7S9210" + depends on ARCH_R7S9210 + help + Say Y here if you want kernel low-level debugging support + via SCIF4 on Renesas RZ/A2M (R7S9210). + config DEBUG_RCAR_GEN1_SCIF0 bool "Kernel low-level debugging messages via SCIF0 on R8A7778" depends on ARCH_R8A7778 @@ -1537,6 +1551,8 @@ config DEBUG_LL_INCLUDE default "debug/msm.S" if DEBUG_QCOM_UARTDM default "debug/omap2plus.S" if DEBUG_OMAP2PLUS_UART default "debug/renesas-scif.S" if DEBUG_R7S72100_SCIF2 + default "debug/renesas-scif.S" if DEBUG_R7S9210_SCIF2 + default "debug/renesas-scif.S" if DEBUG_R7S9210_SCIF4 default "debug/renesas-scif.S" if DEBUG_RCAR_GEN1_SCIF0 default "debug/renesas-scif.S" if DEBUG_RCAR_GEN1_SCIF2 default "debug/renesas-scif.S" if DEBUG_RCAR_GEN2_SCIF0 @@ -1666,7 +1682,8 @@ config DEBUG_UART_PHYS default 0xe6e60000 if DEBUG_RCAR_GEN2_SCIF0 default 0xe6e68000 if DEBUG_RCAR_GEN2_SCIF1 default 0xe6ee0000 if DEBUG_RCAR_GEN2_SCIF4 - default 0xe8008000 if DEBUG_R7S72100_SCIF2 + default 0xe8008000 if DEBUG_R7S72100_SCIF2 || DEBUG_R7S9210_SCIF2 + default 0xe8009000 if DEBUG_R7S9210_SCIF4 default 0xf0000000 if DEBUG_DIGICOLOR_UA0 default 0xf0000be0 if ARCH_EBSA110 default 0xf1012000 if DEBUG_MVEBU_UART0_ALTERNATE @@ -1699,6 +1716,7 @@ config DEBUG_UART_PHYS DEBUG_LL_UART_EFM32 || \ DEBUG_UART_8250 || DEBUG_UART_PL01X || DEBUG_MESON_UARTAO || \ DEBUG_QCOM_UARTDM || DEBUG_R7S72100_SCIF2 || \ + DEBUG_R7S9210_SCIF2 || DEBUG_R7S9210_SCIF4 || \ DEBUG_RCAR_GEN1_SCIF0 || DEBUG_RCAR_GEN1_SCIF2 || \ DEBUG_RCAR_GEN2_SCIF0 || DEBUG_RCAR_GEN2_SCIF1 || \ DEBUG_RCAR_GEN2_SCIF2 || DEBUG_RCAR_GEN2_SCIF4 || \ diff --git a/arch/arm/include/debug/renesas-scif.S b/arch/arm/include/debug/renesas-scif.S index 1c5f795587fc5681..25f06663a9a4e2c1 100644 --- a/arch/arm/include/debug/renesas-scif.S +++ b/arch/arm/include/debug/renesas-scif.S @@ -11,7 +11,11 @@ #define SCIF_PHYS CONFIG_DEBUG_UART_PHYS #define SCIF_VIRT ((SCIF_PHYS & 0x00ffffff) | 0xfd000000) -#if CONFIG_DEBUG_UART_PHYS < 0xe6e00000 +#if defined(CONFIG_DEBUG_R7S9210_SCIF2) || defined(CONFIG_DEBUG_R7S9210_SCIF4) +/* RZ/A2 SCIFA */ +#define FTDR 0x06 +#define FSR 0x08 +#elif CONFIG_DEBUG_UART_PHYS < 0xe6e00000 /* SCIFA */ #define FTDR 0x20 #define FSR 0x14 -- 2.17.1
