[PATCH v3 0/5] ARM: rskrza1: Add RZ/A1 IRQC and input switches

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



	Hi all,

Unlike on most other Renesas SoCs, the GPIO controller block on RZ/A1
and RZ/A2 SoCs lack interrupt functionality.  While the GPIOs can be
routed to the GIC as pin interrupts, this is of limited use, as the
PL390 or GIC-400 supports rising edge and high-level interrupts only.

Fortunately RZ/A1 and RZ/A2 SoCs contain a small front-end for the GIC,
allowing to use up to 8 external interrupts, with configurable sense
select.

Hence this patch series adds DT bindings and a driver for this
front-end, adds a device node for it in the RZ/A1H DTS, and uses it to
enable support for the 3 input switches on the Renesas RSK+RZA1
development board.

Changes compared to v2:
  - Add Tested-by,
  - Use standard interrupt-map instead of custom renesas,gic-spi-base.
    I'm still a bit puzzled by the confusing semantics (double meaning)
    of child and parent unit addresses in interrupt-map.

Changes compared to v1:
  - Add Reviewed-by,
  - Replace gic_spi_base in OF match data by renesas,gic-spi-base in DT,
  - Document RZ/A2M,
  - Use u16 for register values,
  - Use relaxed I/O accessors,
  - Use "rza1-irqc" as irq_chip class name,
  - Enable driver on RZ/A2M.

Dependencies:
  - Patch 3 depends on patch 2,
  - Patch 4 can be applied as soon as the DT bindings in patch 1 have
    been accepted,
  - Patch 5 depends on patch 4.

Upstream strategy:
  - Patches 1-2 are intended to be applied to the irqchip tree,
  - Patches 3-5 are meant for the Renesas tree.

This has been tested on RSK+RZA1 with evtest and s2ram wake-up.
I have verified proper operation of low-level and rising/falling sense
select, too.

Thanks!

Geert Uytterhoeven (5):
  dt-bindings: interrupt-controller: Add Renesas RZ/A1 Interrupt
    Controller
  irqchip: Add Renesas RZ/A1 Interrupt Controller driver
  soc: renesas: Enable RZ/A1 IRQC on RZ/A1H and RZ/A2M
  ARM: dts: r7s72100: Add IRQC device node
  ARM: dts: rskrza1: Add input switches

 .../renesas,rza1-irqc.txt                     |  43 +++
 arch/arm/boot/dts/r7s72100-rskrza1.dts        |  38 +++
 arch/arm/boot/dts/r7s72100.dtsi               |  19 ++
 drivers/irqchip/Kconfig                       |   4 +
 drivers/irqchip/Makefile                      |   1 +
 drivers/irqchip/irq-renesas-rza1.c            | 283 ++++++++++++++++++
 drivers/soc/renesas/Kconfig                   |   4 +-
 7 files changed, 391 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/interrupt-controller/renesas,rza1-irqc.txt
 create mode 100644 drivers/irqchip/irq-renesas-rza1.c

-- 
2.17.1

Gr{oetje,eeting}s,

						Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
							    -- Linus Torvalds



[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux