Hi Jacopo,
On Fri, Mar 08, 2019 at 06:32:59PM +0100, Jacopo Mondi wrote:
> On Thu, Mar 07, 2019 at 01:23:36AM +0200, Laurent Pinchart wrote:
> > Set a drm_bridge_timings in the drm_bridge, and use it to report the
> > input bus mode (single-link or dual-link). The other fields of the
> > timings structure are kept to 0 as they do not apply to LVDS buses.
> >
> > Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@xxxxxxxxxxxxxxxx>
> > ---
> > drivers/gpu/drm/bridge/thc63lvd1024.c | 46 ++++++++++++++++++++-------
> > 1 file changed, 35 insertions(+), 11 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/bridge/thc63lvd1024.c b/drivers/gpu/drm/bridge/thc63lvd1024.c
> > index b083a740565c..206b0af5e154 100644
> > --- a/drivers/gpu/drm/bridge/thc63lvd1024.c
> > +++ b/drivers/gpu/drm/bridge/thc63lvd1024.c
> > @@ -31,6 +31,8 @@ struct thc63_dev {
> >
> > struct drm_bridge bridge;
> > struct drm_bridge *next;
> > +
> > + struct drm_bridge_timings timings;
> > };
> >
> > static inline struct thc63_dev *to_thc63(struct drm_bridge *bridge)
> > @@ -48,15 +50,28 @@ static int thc63_attach(struct drm_bridge *bridge)
> > static enum drm_mode_status thc63_mode_valid(struct drm_bridge *bridge,
> > const struct drm_display_mode *mode)
> > {
> > + struct thc63_dev *thc63 = to_thc63(bridge);
> > + unsigned int min_freq;
> > + unsigned int max_freq;
> > +
> > /*
> > - * The THC63LVD1024 clock frequency range is 8 to 135 MHz in single-in
> > - * mode. Note that the limits are different in dual-in, single-out mode,
> > - * and will need to be adjusted accordingly.
> > + * The THC63LVD1024 pixel rate range is 8 to 135 MHz in all modes but
> > + * dual-in, single-out where it is 40 to 150 MHz. As dual-in, dual-out
> > + * isn't supported by the driver yet, simply derive the limits from the
> > + * input mode.
> > */
> > - if (mode->clock < 8000)
> > + if (thc63->timings.dual_link) {
> > + min_freq = 40000;
> > + max_freq = 150000;
> > + } else {
> > + min_freq = 8000;
> > + max_freq = 135000;
> > + }
> > +
> > + if (mode->clock < min_freq)
> > return MODE_CLOCK_LOW;
> >
> > - if (mode->clock > 135000)
> > + if (mode->clock > max_freq)
> > return MODE_CLOCK_HIGH;
> >
> > return MODE_OK;
> > @@ -101,19 +116,19 @@ static const struct drm_bridge_funcs thc63_bridge_func = {
> >
> > static int thc63_parse_dt(struct thc63_dev *thc63)
> > {
> > - struct device_node *thc63_out;
> > + struct device_node *endpoint;
> > struct device_node *remote;
> >
> > - thc63_out = of_graph_get_endpoint_by_regs(thc63->dev->of_node,
> > - THC63_RGB_OUT0, -1);
> > - if (!thc63_out) {
> > + endpoint = of_graph_get_endpoint_by_regs(thc63->dev->of_node,
> > + THC63_RGB_OUT0, -1);
> > + if (!endpoint) {
> > dev_err(thc63->dev, "Missing endpoint in port@%u\n",
> > THC63_RGB_OUT0);
> > return -ENODEV;
> > }
> >
> > - remote = of_graph_get_remote_port_parent(thc63_out);
> > - of_node_put(thc63_out);
> > + remote = of_graph_get_remote_port_parent(endpoint);
> > + of_node_put(endpoint);
> > if (!remote) {
> > dev_err(thc63->dev, "Endpoint in port@%u unconnected\n",
> > THC63_RGB_OUT0);
> > @@ -132,6 +147,14 @@ static int thc63_parse_dt(struct thc63_dev *thc63)
> > if (!thc63->next)
> > return -EPROBE_DEFER;
> >
> > + endpoint = of_graph_get_endpoint_by_regs(thc63->dev->of_node,
> > + THC63_LVDS_IN1, -1);
> > + of_node_put(endpoint);
> > +
>
> Should you check if endpoint is enabled?
Can endpoints be disabled ?
> By the way, this seems to me works properly, as in [12/15] if skip
> creation of the LVDS1 encoder if it is operating in dual link mode.
> Without that, we would hit again the issue of matching on device
> nodes, as the same bridge would be attached twice, am I wrong?
>
> I feel we've been there already :)
> https://lkml.org/lkml/2018/3/20/341
>
> and it is not just an issue on matching on endpoints, it's that the
> drm bridge itself that would need to handle multiple attach/detaches..
Correct. Thanks to 12/15 we don't need this yet :-)
> > + thc63->timings.dual_link = endpoint != NULL;
> > + dev_dbg(thc63->dev, "operating in %s-link mode\n",
> > + thc63->timings.dual_link ? "dual" : "single");
> > +
> > return 0;
> > }
> >
> > @@ -188,6 +211,7 @@ static int thc63_probe(struct platform_device *pdev)
> > thc63->bridge.driver_private = thc63;
> > thc63->bridge.of_node = pdev->dev.of_node;
> > thc63->bridge.funcs = &thc63_bridge_func;
> > + thc63->bridge.timings = &thc63->timings;
> >
> > drm_bridge_add(&thc63->bridge);
> >
--
Regards,
Laurent Pinchart
