Re: [PATCH v2 3/3] sh_eth: add R8A77980 support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 12/30/2018 08:24 PM, Sergei Shtylyov wrote:

>> Finally, add support for the DT probing of the R-Car V3H (AKA R8A77980) --
>> it's the only R-Car gen3 SoC having the GEther controller -- others have
>> only EtherAVB...
>>
>> Based on the original (and large) patch by Vladimir Barinov.
>>
>> Signed-off-by: Vladimir Barinov <vladimir.barinov@xxxxxxxxxxxxxxxxxx>
>> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@xxxxxxxxxxxxxxxxxx>
>> Reviewed-by: Simon Horman <horms+renesas@xxxxxxxxxxxx>
>>
> [...]
>> Index: net-next/drivers/net/ethernet/renesas/sh_eth.c
>> ===================================================================
>> --- net-next.orig/drivers/net/ethernet/renesas/sh_eth.c
>> +++ net-next/drivers/net/ethernet/renesas/sh_eth.c
>> @@ -753,6 +753,49 @@ static struct sh_eth_cpu_data rcar_gen2_
>>  	.rmiimode	= 1,
>>  	.magic		= 1,
>>  };
>> +
>> +/* R8A77980 */
>> +static struct sh_eth_cpu_data r8a77980_data = {
>> +	.soft_reset	= sh_eth_soft_reset_gether,
>> +
>> +	.set_duplex	= sh_eth_set_duplex,
>> +	.set_rate	= sh_eth_set_rate_gether,
>> +
>> +	.register_type  = SH_ETH_REG_GIGABIT,
>> +
>> +	.edtrr_trns	= EDTRR_TRNS_GETHER,
>> +	.ecsr_value	= ECSR_PSRTO | ECSR_LCHNG | ECSR_ICD | ECSR_MPD,
>> +	.ecsipr_value	= ECSIPR_PSRTOIP | ECSIPR_LCHNGIP | ECSIPR_ICDIP |
>> +			  ECSIPR_MPDIP,
>> +	.eesipr_value	= EESIPR_RFCOFIP | EESIPR_ECIIP |
>> +			  EESIPR_FTCIP | EESIPR_TDEIP | EESIPR_TFUFIP |
>> +			  EESIPR_FRIP | EESIPR_RDEIP | EESIPR_RFOFIP |
>> +			  EESIPR_RMAFIP | EESIPR_RRFIP |
>> +			  EESIPR_RTLFIP | EESIPR_RTSFIP |
>> +			  EESIPR_PREIP | EESIPR_CERFIP,
>> +
>> +	.tx_check       = EESR_FTC | EESR_CD | EESR_RTO,
>> +	.eesr_err_check = EESR_TWB1 | EESR_TWB | EESR_TABT | EESR_RABT |
>> +			  EESR_RFE | EESR_RDE | EESR_RFRMER |
>> +			  EESR_TFE | EESR_TDE | EESR_ECI,
>> +	.fdr_value	= 0x0000070f,
>> +
>> +	.apr		= 1,
>> +	.mpr		= 1,
>> +	.tpauser	= 1,
>> +	.bculr		= 1,
>> +	.hw_swap	= 1,
>> +	.nbst		= 1,
>> +	.rpadir		= 1,
>> +	.rpadir_value   = 2 << 16,
>> +	.no_trimd	= 1,
>> +	.no_ade		= 1,
>> +	.xdfar_rw	= 1,
>> +	.hw_checksum	= 1,
> 
>    Ugh, the "intelligent" checksum is not actually supported, just a simplistic
> checksum (from byte 14). I'll send a fix.

   Surprisingly, testing has shown that the manual is wrong and thus "intelligent"
checksumming is implemented. When I remove that flag, DHCP doesn't work.

>> +	.select_mii	= 1,
>> +	.magic		= 1,
>> +	.cexcr		= 1,
>> +};
>>  #endif /* CONFIG_OF */
>>  
>>  static void sh_eth_set_rate_sh7724(struct net_device *ndev)
> [...]

MBR, Sergei



[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux