Re: [PATCH v3 4/4] i2c: adv748x: configure number of lanes used for TXA CSI-2 transmitter

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Niklas,

On Fri, Nov 02, 2018 at 05:00:09PM +0100, Niklas Söderlund wrote:
> The driver fixed the TXA CSI-2 transmitter in 4-lane mode while it could
> operate using 1-, 2- and 4-lanes. Update the driver to support all modes
> the hardware does.
>
> The driver make use of large tables of static register/value writes when
> powering up/down the TXA and TXB transmitters which include the write to
> the NUM_LANES register. By converting the tables into functions and
> using parameters the power up/down functions for TXA and TXB power
> up/down can be merged and used for both transmitters.
>
> Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@xxxxxxxxxxxx>
>
> ---
> * Changes since v2
> - Fix typos in comments.
> - Remove unneeded boiler plait code in adv748x_tx_power() as suggested
>   by Jacopo and Laurent.
> - Take into account the two different register used when powering up TXA
>   and TXB due to an earlier patch in this series aligns the power
>   sequence with the manual.
>
> * Changes since v1
> - Convert tables of register/value writes into functions instead of
>   intercepting and modifying the writes to the NUM_LANES register.
> ---
>  drivers/media/i2c/adv748x/adv748x-core.c | 157 ++++++++++++-----------
>  1 file changed, 79 insertions(+), 78 deletions(-)
>
> diff --git a/drivers/media/i2c/adv748x/adv748x-core.c b/drivers/media/i2c/adv748x/adv748x-core.c
> index 9d80d7f3062b16bc..d94c63cb6a2efdba 100644
> --- a/drivers/media/i2c/adv748x/adv748x-core.c
> +++ b/drivers/media/i2c/adv748x/adv748x-core.c
> @@ -125,6 +125,16 @@ int adv748x_write(struct adv748x_state *state, u8 page, u8 reg, u8 value)
>  	return regmap_write(state->regmap[page], reg, value);
>  }
>
> +static int adv748x_write_check(struct adv748x_state *state, u8 page, u8 reg,
> +			       u8 value, int *error)
> +{
> +	if (*error)
> +		return *error;
> +
> +	*error = adv748x_write(state, page, reg, value);
> +	return *error;
> +}
> +
>  /* adv748x_write_block(): Write raw data with a maximum of I2C_SMBUS_BLOCK_MAX
>   * size to one or more registers.
>   *
> @@ -231,79 +241,77 @@ static int adv748x_write_regs(struct adv748x_state *state,
>   * TXA and TXB
>   */
>
> -static const struct adv748x_reg_value adv748x_power_up_txa_4lane[] = {
> -
> -	{ADV748X_PAGE_TXA, 0x00, 0x84},	/* Enable 4-lane MIPI */
> -	{ADV748X_PAGE_TXA, 0x00, 0xa4},	/* Set Auto DPHY Timing */
> -	{ADV748X_PAGE_TXA, 0xdb, 0x10},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0xd6, 0x07},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0xc4, 0x0a},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0x71, 0x33},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0x72, 0x11},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0xf0, 0x00},	/* i2c_dphy_pwdn - 1'b0 */
> -
> -	{ADV748X_PAGE_TXA, 0x31, 0x82},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0x1e, 0x40},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0xda, 0x01},	/* i2c_mipi_pll_en - 1'b1 */
> -	{ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */
> -	{ADV748X_PAGE_TXA, 0x00, 0x24 },/* Power-up CSI-TX */
> -	{ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */
> -	{ADV748X_PAGE_TXA, 0xc1, 0x2b},	/* ADI Required Write */
> -	{ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */
> -	{ADV748X_PAGE_TXA, 0x31, 0x80},	/* ADI Required Write */
> -
> -	{ADV748X_PAGE_EOR, 0xff, 0xff}	/* End of register table */
> -};
> -
> -static const struct adv748x_reg_value adv748x_power_down_txa_4lane[] = {
> -
> -	{ADV748X_PAGE_TXA, 0x31, 0x82},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0x1e, 0x00},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXA, 0x00, 0x84},	/* Enable 4-lane MIPI */
> -	{ADV748X_PAGE_TXA, 0xda, 0x01},	/* i2c_mipi_pll_en - 1'b1 */
> -	{ADV748X_PAGE_TXA, 0xc1, 0x3b},	/* ADI Required Write */
> -
> -	{ADV748X_PAGE_EOR, 0xff, 0xff}	/* End of register table */
> -};
> -
> -static const struct adv748x_reg_value adv748x_power_up_txb_1lane[] = {
> -
> -	{ADV748X_PAGE_TXB, 0x00, 0x81},	/* Enable 1-lane MIPI */
> -	{ADV748X_PAGE_TXB, 0x00, 0xa1},	/* Set Auto DPHY Timing */
> -	{ADV748X_PAGE_TXB, 0xd2, 0x40},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0xc4, 0x0a},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0x71, 0x33},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0x72, 0x11},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0xf0, 0x00},	/* i2c_dphy_pwdn - 1'b0 */
> -
> -	{ADV748X_PAGE_TXB, 0x31, 0x82},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0x1e, 0x40},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0xda, 0x01},	/* i2c_mipi_pll_en - 1'b1 */
> -	{ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */
> -	{ADV748X_PAGE_TXB, 0x00, 0x21 },/* Power-up CSI-TX */
> -	{ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */
> -	{ADV748X_PAGE_TXB, 0xc1, 0x2b},	/* ADI Required Write */
> -	{ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */
> -	{ADV748X_PAGE_TXB, 0x31, 0x80},	/* ADI Required Write */
> -
> -	{ADV748X_PAGE_EOR, 0xff, 0xff}	/* End of register table */
> -};
> -
> -static const struct adv748x_reg_value adv748x_power_down_txb_1lane[] = {
> -
> -	{ADV748X_PAGE_TXB, 0x31, 0x82},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0x1e, 0x00},	/* ADI Required Write */
> -	{ADV748X_PAGE_TXB, 0x00, 0x81},	/* Enable 1-lane MIPI */
> -	{ADV748X_PAGE_TXB, 0xda, 0x01},	/* i2c_mipi_pll_en - 1'b1 */
> -	{ADV748X_PAGE_TXB, 0xc1, 0x3b},	/* ADI Required Write */
> -
> -	{ADV748X_PAGE_EOR, 0xff, 0xff}	/* End of register table */
> -};
> +static int adv748x_power_up_tx(struct adv748x_csi2 *tx)
> +{
> +	struct adv748x_state *state = tx->state;
> +	u8 page = is_txa(tx) ? ADV748X_PAGE_TXA : ADV748X_PAGE_TXB;
> +	int ret = 0;
> +
> +	/* Enable n-lane MIPI */
> +	adv748x_write_check(state, page, 0x00, 0x80 | tx->num_lanes, &ret);
> +
> +	/* Set Auto DPHY Timing */
> +	adv748x_write_check(state, page, 0x00, 0xa0 | tx->num_lanes, &ret);
> +
> +	/* ADI Required Write */
> +	if (is_txa(tx)) {
> +		adv748x_write_check(state, page, 0xdb, 0x10, &ret);
> +		adv748x_write_check(state, page, 0xd6, 0x07, &ret);
> +	} else {
> +		adv748x_write_check(state, page, 0xd2, 0x40, &ret);
> +	}
> +
> +	adv748x_write_check(state, page, 0xc4, 0x0a, &ret);
> +	adv748x_write_check(state, page, 0x71, 0x33, &ret);
> +	adv748x_write_check(state, page, 0x72, 0x11, &ret);
> +
> +	/* i2c_dphy_pwdn - 1'b0 */
> +	adv748x_write_check(state, page, 0xf0, 0x00, &ret);
> +
> +	/* ADI Required Writes*/
> +	adv748x_write_check(state, page, 0x31, 0x82, &ret);
> +	adv748x_write_check(state, page, 0x1e, 0x40, &ret);
> +
> +	/* i2c_mipi_pll_en - 1'b1 */
> +	adv748x_write_check(state, page, 0xda, 0x01, &ret);
> +	usleep_range(2000, 2500);
> +
> +	/* Power-up CSI-TX */
> +	adv748x_write_check(state, page, 0x00, 0x20 | tx->num_lanes, &ret);

Where does the 0x20 come from? I don't see it in the register
description in the HW manual..

> +	usleep_range(1000, 1500);
> +
> +	/* ADI Required Writes */
> +	adv748x_write_check(state, page, 0xc1, 0x2b, &ret);
> +	usleep_range(1000, 1500);
> +	adv748x_write_check(state, page, 0x31, 0x80, &ret);
> +
> +	return ret;
> +}
> +
> +static int adv748x_power_down_tx(struct adv748x_csi2 *tx)
> +{
> +	struct adv748x_state *state = tx->state;
> +	u8 page = is_txa(tx) ? ADV748X_PAGE_TXA : ADV748X_PAGE_TXB;
> +	int ret = 0;
> +
> +	/* ADI Required Writes */
> +	adv748x_write_check(state, page, 0x31, 0x82, &ret);
> +	adv748x_write_check(state, page, 0x1e, 0x00, &ret);
> +
> +	/* Enable n-lane MIPI */

The comment is wrong here: this write disables the CSI TX interface.

> +	adv748x_write_check(state, page, 0x00, 0x80 | tx->num_lanes, &ret);
> +
> +	/* i2c_mipi_pll_en - 1'b1 */
> +	adv748x_write_check(state, page, 0xda, 0x01, &ret);

Re-looking at power up/down sequences, this should actually be 0xda = 0x00,
as specified in seciont 9.5.2 of the HW manual.

I know all of these come from tables in the previous version and has not
been introduced by this patch, but while at there it might be worth
fixing them.

And actually, I don't like much the comments for registers pll_en and
dphy_pdn registers, and they might be improved, since you're rewriting
this sequence anyhow.

I had a patch pending, before I realized you could change this in your
next v4. In case you want to have a look:
https://paste.debian.net/1052965/

Thanks
   j

> +
> +	/* ADI Required Write */
> +	adv748x_write_check(state, page, 0xc1, 0x3b, &ret);
> +
> +	return ret;
> +}
>
>  int adv748x_tx_power(struct adv748x_csi2 *tx, bool on)
>  {
> -	struct adv748x_state *state = tx->state;
> -	const struct adv748x_reg_value *reglist;
>  	int val;
>
>  	if (!is_tx_enabled(tx))
> @@ -321,14 +329,7 @@ int adv748x_tx_power(struct adv748x_csi2 *tx, bool on)
>  	WARN_ONCE((on && val & ADV748X_CSI_FS_AS_LS_UNKNOWN),
>  			"Enabling with unknown bit set");
>
> -	if (on)
> -		reglist = is_txa(tx) ? adv748x_power_up_txa_4lane :
> -				       adv748x_power_up_txb_1lane;
> -	else
> -		reglist = is_txa(tx) ? adv748x_power_down_txa_4lane :
> -				       adv748x_power_down_txb_1lane;
> -
> -	return adv748x_write_regs(state, reglist);
> +	return on ? adv748x_power_up_tx(tx) : adv748x_power_down_tx(tx);
>  }
>
>  /* -----------------------------------------------------------------------------
> --
> 2.19.1
>

Attachment: signature.asc
Description: PGP signature


[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux