RE: [PATCH 2/3] phy: renesas: rcar-gen3-usb2: Add support for R7S9210

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Shimodaさん

> From: Yoshihiro Shimoda
> Sent: Thursday, November 15, 2018 4:20 AM

> > Host does NOT work:
> > 	//else
> > 	//	/* No otg, so default to host mode */
> > 	//	writel(0x00000000, usb2_base + USB2_COMMCTRL);
> 
> I got it. However, I have a concern how to set the mode to peripheral on
> RZ/A2
> if we applied this code. If someone would like to use the USB as
> peripheral
> on his board, this code is not suitable.

But USB peripheral is a different driver. So, this code will not run. So
USB2_COMMCTRL will keep the default value 0x80000000.

Correct?

> So, I have an idea to set the default mode by using "dr_mode" property,
> instead of hardcoded. Since the driver already has such a function,
> we can reuse rcar_gen3_device_recognition() to set the default value.
> To achieve that, we need to modify the following though.
>  - Don't enable "is_otg_channel".
>  - Don't call rcar_gen3_enable_vbus_ctrl() to avoid ADPCTRL register
>    because RZ/A2 doesn't have it.
>  - Don't need to call rcar_gen3_set_linectrl to avoid LINECTRL1 register
>    because RZ/A2 doesn't seem to need the setting on host mode.
> 
> What do you think?

If a board is designed for USB peripheral, why would they enable a EHCI 
host driver for the same USB channel?
I am confused.

> > > (In other words, if we use the port as peripheral with the reset value
> > > 0x80000000, does it work?)
> >
> > We have not been able to get USB peripheral working on RZ/A2 yet.
> > For peripheral, RZ/A2 has HS-USB.
> > After plugging into the PC, HS-USB goes to Suspended state (DVSQ =
> "0110").
> > It should go to Configured state (DVSQ = "0011")
> 
> I guess we need to modify ./drivers/usb/renesas_usbhs/rza.c for RZ/A2
> because RZ/A2's HS-USB has SYSCFG.CNEN, but doesn't have SYSCFG.UPLLE?

Today for RZ/A1, we tell people to use USB0 first in their board design,
then use USB1 if they need a second USB channel. USB pins are dedicated
(no other function) so there should be no design conflicts.

If only USB1 is used, USB0 must also be enabled in DT as a dummy driver 
(so SYSCFG.UPLLE can get set for USB1).


> > According to the RZ/A2 Hardware Manual, COMMCTRL should be 0x80000000
> when
> > using HS-USB.
> >
> > There are 2 channels of USB on RZ/A2 (host x 2, HS_USB x 2)
> 
> I got it. So, I guess someone wants to use 1 host and 1 peripheral :)

Yes.

Chris





[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux