[PATCH 4/4] ARM: dts: iwg23s-sbc: Add uSD card support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add uSD card support to the iwg23s single board computer powered
by the RZ/G1C SoC (a.k.a. r8a77470).

Signed-off-by: Fabrizio Castro <fabrizio.castro@xxxxxxxxxxxxxx>
Reviewed-by: Biju Das <biju.das@xxxxxxxxxxxxxx>
---
Hello Simon,

this patch can only be taken after patch "pinctrl: sh-pfc: r8a77470:
Add SDHI2 voltage switch" from this series appears on a release candidate
or a release.
Shall I re-send it at a later stage or are you happy to keep it around
and defer its application to when its dependency is sorted?

Thanks,
Fab

 arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts | 49 +++++++++++++++++++++++++++++++
 1 file changed, 49 insertions(+)

diff --git a/arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts b/arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts
index 22da819..cd9c3fc 100644
--- a/arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts
+++ b/arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts
@@ -6,6 +6,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
 #include "r8a77470.dtsi"
 / {
 	model = "iWave iW-RainboW-G23S single board computer based on RZ/G1C";
@@ -25,6 +26,29 @@
 		device_type = "memory";
 		reg = <0 0x40000000 0 0x20000000>;
 	};
+
+	vcc_sdhi2: regulator-vcc-sdhi2 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "SDHI2 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		enable-active-high;
+	};
+
+	vccq_sdhi2: regulator-vccq-sdhi2 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI2 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio2 24 GPIO_ACTIVE_LOW>;
+		gpios-states = <1>;
+		states = <3300000 1
+			  1800000 0>;
+	};
 };
 
 &avb {
@@ -50,6 +74,18 @@
 		groups = "scif1_data_b";
 		function = "scif1";
 	};
+
+	sdhi2_pins: sd2 {
+		groups = "sdhi2_data4", "sdhi2_ctrl";
+		function = "sdhi2";
+		power-source = <3300>;
+	};
+
+	sdhi2_pins_uhs: sd2_uhs {
+		groups = "sdhi2_data4", "sdhi2_ctrl";
+		function = "sdhi2";
+		power-source = <1800>;
+	};
 };
 
 &scif1 {
@@ -58,3 +94,16 @@
 
 	status = "okay";
 };
+
+&sdhi2 {
+	pinctrl-0 = <&sdhi2_pins>;
+	pinctrl-1 = <&sdhi2_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&vcc_sdhi2>;
+	vqmmc-supply = <&vccq_sdhi2>;
+	bus-width = <4>;
+	cd-gpios = <&gpio4 20 GPIO_ACTIVE_LOW>;
+	sd-uhs-sdr50;
+	status = "okay";
+};
-- 
2.7.4




[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux