Hi Geert,
Thanks for your work.
On 2018-07-16 17:30:51 +0200, Geert Uytterhoeven wrote:
> Extend the existing support for backup mode to toggle power switches.
> With a toggle power switch (or level signal), the following steps must
> be followed exactly:
> 1. Configure PMIC for backup mode, to change the role of the
> accessory power switch from a power switch to a wake-up switch,
> 2. Switch accessory power switch off, to prepare for system suspend,
> which is a manual step not controlled by software,
> 3. Suspend system,
> 4. Switch accessory power switch on, to resume the system.
>
> Hence the PMIC is configured for backup mode when "on" or "1" is written
> to the PMIC's "backup_mode" virtual file in sysfs. Conversely, writing
> "off" or "0" reverts the role of the accessory switch to a power
> switch.
>
> Unlike with momentary switches, backup mode is not enabled by default,
> as enabling it prevents the board from being powered off using the power
> switch, which may confuse the user.
>
> Signed-off-by: Geert Uytterhoeven <geert+renesas@xxxxxxxxx>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@xxxxxxxxxxxx>
> ---
> v4:
> - Improve patch description and comment,
>
> v3:
> - Replace use of "wake_up" sysfs file and extra callback for wake-up
> change notification by custom "backup_mode" sysfs file,
>
> v2:
> - Improve patch description,
> - Drop "return;" at end of function.
> ---
> drivers/regulator/bd9571mwv-regulator.c | 20 ++++++++++++++++++++
> 1 file changed, 20 insertions(+)
>
> diff --git a/drivers/regulator/bd9571mwv-regulator.c b/drivers/regulator/bd9571mwv-regulator.c
> index 1da36a6590c84ba4..c44613b9423baf07 100644
> --- a/drivers/regulator/bd9571mwv-regulator.c
> +++ b/drivers/regulator/bd9571mwv-regulator.c
> @@ -185,6 +185,7 @@ static ssize_t backup_mode_store(struct device *dev,
> const char *buf, size_t count)
> {
> struct bd9571mwv_reg *bdreg = dev_get_drvdata(dev);
> + unsigned int mode;
> int ret;
>
> if (!count)
> @@ -194,6 +195,25 @@ static ssize_t backup_mode_store(struct device *dev,
> if (ret)
> return ret;
>
> + if (!bdreg->rstbmode_level)
> + return count;
> +
> + /*
> + * Configure DDR Backup Mode, to change the role of the accessory power
> + * switch from a power switch to a wake-up switch, or vice versa
> + */
> + ret = bd9571mwv_bkup_mode_read(bdreg->bd, &mode);
> + if (ret)
> + return ret;
> +
> + mode &= ~BD9571MWV_BKUP_MODE_CNT_KEEPON_MASK;
> + if (bdreg->bkup_mode_enabled)
> + mode |= bdreg->bkup_mode_cnt_keepon;
> +
> + ret = bd9571mwv_bkup_mode_write(bdreg->bd, mode);
> + if (ret)
> + return ret;
> +
> return count;
> }
>
> --
> 2.17.1
>
--
Regards,
Niklas Söderlund
