Re: [PATCH v5] gpio: dwapb: Add support for 1 interrupt per port A GPIO

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, Apr 26, 2018 at 7:19 PM, Phil Edworthy
<phil.edworthy@xxxxxxxxxxx> wrote:

Sotty fo a late response. Consider follow up fixes for below.

>         if (!pp->irq_shared) {
> +               int i;
> +
> +               for (i = 0; i < pp->ngpio; i++) {
> +                       if (pp->irq[i])
> +                               irq_set_chained_handler_and_data(pp->irq[i],
> +                                               dwapb_irq_handler, gpio);
> +               }
>         } else {
>                 /*
>                  * Request a shared IRQ since where MFD would have devices
>                  * using the same irq pin
>                  */
> +               err = devm_request_irq(gpio->dev, pp->irq[0],
>                                        dwapb_irq_handler_mfd,
>                                        IRQF_SHARED, "gpio-dwapb-mfd", gpio);

> +       if (pp->has_irq)
>                 dwapb_configure_irqs(gpio, port, pp);

I would rather make irq array a type of signed int and move
conditional into the function to test per IRQ based.

>         /* Add GPIO-signaled ACPI event support */
> +       if (pp->has_irq)
>                 acpi_gpiochip_request_interrupts(&port->gc);

Perhaps something similar.

>                 if (dev->of_node && pp->idx == 0 &&
>                         fwnode_property_read_bool(fwnode,
>                                                   "interrupt-controller")) {

> +                       struct device_node *np = to_of_node(fwnode);
> +                       unsigned int j;
> +
> +                       /*
> +                        * The IP has configuration options to allow a single
> +                        * combined interrupt or one per gpio. If one per gpio,
> +                        * some might not be used.
> +                        */
> +                       for (j = 0; j < pp->ngpio; j++) {
> +                               int irq = of_irq_get(np, j);
> +                               if (irq < 0)
> +                                       continue;
> +
> +                               pp->irq[j] = irq;
> +                               pp->has_irq = true;
> +                       }

for (...)
 pp->irq = of_irq_get();

>                 }

> +               if (has_acpi_companion(dev) && pp->idx == 0) {
> +                       unsigned int j;
> +
> +                       for (j = 0; j < pp->ngpio; j++) {
> +                               pp->irq[j] = platform_get_irq(to_platform_device(dev), j);
> +                               if (pp->irq[j])
> +                                       pp->has_irq = true;
> +                       }

Ditto.
Moreover you have a bug here. See my proposal at the top of this message.

And now even better to ask, why platform_get_irq() wouldn't work for DT case?

> +
> +                       if (!pp->has_irq)
>                                 dev_warn(dev, "no irq for port%d\n", pp->idx);

This could be issued in the actual function which will try to allocate
IRQs (perhaps on debug level)


P.S. Just think about it, perhaps you find even better solutions.

-- 
With Best Regards,
Andy Shevchenko



[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux